Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Painting my house Question? (OT)

Posts

Painting my house Question? (OT)

#1

Painting my house Question? (OT)

Barry Irby

>My house has rough sawn fir T 1-ll. The paint is peeling.

Is it acceptable to power wash it to remove the loose paint?

What is the best way to prep for painting?

What is the best primer? The Best paint/stain. any idea of costs?

Re: Painting my house Question? (OT)

#2

Re: Painting my house Question? (OT)

Nat Robison

>Your questions are pretty open-ended and subject to widely varying opinions......kind of like "What's the best table saw?"

I've seen your type of siding power-washed prior to painting and it seemed to remove a ton of dirt. You need to give the siding a chance to thouroughly dry out before painting.

The main painting contractor on This Old House generally primes with oil-based and then tops with two coats of latex. You could probably go all latex and get good results. You could buy all your paint from Home Depot but contractors usually get their supplies from Sherwin-Williams or other paint-only stores.

Can't really say how much your job would cost, it all depends on the amount of woodwork to be painted......I do know that your type of siding tends to suck up the paint so you may not get the coverage that other types of woodwork/siding might get. As most painters will tell you, good prep is 90% of the job. Laying on the paint is the easiest part of a quality job.

I'm not a painter but I worked for one in college and I always got stuck painting closets. I swear I'm a little dumber for it to this day due to the fumes.

Re: Painting my house Question? (OT)

#3

Re: Painting my house Question? (OT)------WebKitFo

paul in AZ------WebKitFormBoundary+isMX5X2paiDYC5e

>When I lived in Tucson, my house was mostly burnt adobe but had some T 1-11.

I pressure washed it.

No primer.

I used the best paint available in the area -which around here is Dunn Edwards. This is a regional western states brand. Ask a pro painter for a recommendation. Cutting cost on paint is poor economy.

I brushed mine on in a heavy coat and got one coat coverage. Partly a preference of mine and partly because the paint is so think it doesn't spray well without big time equipment.

Is that the "best" way to do it? I don't know but it worked for me.

------WebKitFormBoundary+isMX5X2paiDYC5e

Re: Painting my house Question? (OT)

#4

Correction -should be 'thick'

paul in AZ------WebKitFormBoundary+isMX5X2paiDYC5e

>

Re: Painting my house Question? (OT)

#5

Re: Painting my house Question? (OT)

Joseph Mulherin, Sr

>Barry, Nat is probably correct in his advise. I will tell you my ideas: Go to the HD or Lowes, buy some KILLZ primer. Normally a gallon will cover about 400sqft. I thin down my latex for my air sprayer thusly....mix in one(1) quart of water into the paint...stir very well, strain it all thru a cheese cloth strainer, pour mixture into your quart spraygun cup, set the pressure at 35lbs, then just go to it and spray where you want. After applying the Killz, let it dry throughly, then mixup and apply your final color on the house. While spraying latex you are going to get a setting on the nozzel, so wipe it with you gloved hand to clean off and keep on spraying. Paint trim with a brush. Mask off all windows and doors first before spraying.

Others may have some other ideas but those are mine. Good luck.

Re: Painting my house Question? (OT)

#6

Re: Painting my house Question? (OT)

GalenV in Iowa

>What is on your rough saw now that is peeling, oil base or latex?

Was it a transparent or solid stain or paint?

If peeling then I would guess latex paint and once water is behind latex it will rot or peel. Latex is poor to put over rough saw but that is what gets put on a lot of time because people think it covers well. If it is latex then you will need to use latex over it not oil, as not much choice.

I think oil is best on rough saw as it will not trap moisture as bad. Preserves the wood better.

If you power wash then it is going to take a long time to dry out and not sure what you climate is like, could take a month. High pressure really puts moisture deep into wood. Not knowing how bad it is wire brush may be better.

Just my opinion as I have replaced cedar rough saw siding when home had latex on it. Never had a problem again with oil.

Painted houses and too many farm buildings in my younger days when farmers wanted brush over thin spray jobs.

Galen

Re: Painting my house Question? (OT)

#7

Re: Painting my house Question? (OT)

Glenn Madsen near San Francisco

>I'm in California, so take with a grain of salt anything I tell you. We have rules here that often differ from the rest of the country, and I don't want to argue what's correct or best. We get to follow the rules here...

My house is T-111 and stucco. Painting the T-111 BEFORE it gets cracked and loose is strongly preferred, but I understand you haven't that luxury. The folks who indicate that power washing needs to be let dry completely are correct. Here, that takes less than a week. My concern is catching the wash-off if your flaking pain has lead in it. It may not, but some of those houses are older, and yours may. Lead test kits are cheap and available.

A sander and a vacuum attachment with HEPA filter may take care of your sanding dust as well, and keep the power wash off-flow under control. Wear a mask...

The primer recommendations sound correct, regards oil/latex, etc. So does the recommendation not to skimp on paint. Find out who is the best manufacturer of paint in your region, and buy their product from a professional outlet. You'll get the best product, but you'll also be able to rent the best airless sprayer there for your job. THOSE are the best tools to come along for painters in the last 50 years or so. Purdy brushes. Good quality CLOTH drop cloths. And buckets, tape, sponges, wire brushes, caulk, and on and on and on.

If you do it right, it will not need doing again for at least ten years, and maybe longer.

Mine gets done more frequently because LOML wants a color change. ;-)

Re: Painting my house Question? (OT)

#8

Re: Painting Cost

GalenV in Iowa

>I agree with the people who suggest quality paint and equipment. Do not be mislead by the normal advertised cost of quality paint verses Home Depot or Lowes. I found I could get better pricing from Sherwin Williams when they knew I was going to need 30 gallons of stain. In my case I was not sure how much stain I would need for rough out cedar horizontal siding. Walk out ranch so two story on one side and lots of windows. Hard to figure. They just started off mixing me batches as needed and always blended as I went back for more.

This went on by brush so they just about gave me quality brushes as even then I went through a lot of them on rough out. Think I ended up with a few more gallons when done.

Fortunately a friend had scaffolding so cost me nothing to use other than a few new planks.

This is the time you hit friends up for any paybacks.

My oldest daughter had a painting party for her home. Cook out and drinks got a lot done for her.

Galen

Re: Painting my house Question? (OT)

#9

Re: Painting my house Question? (OT)

Fred Davis

>That is the siding we used on this place, though it is resawn , not rough sawed, there is a distinct difference and I have never seen Texture 1-11 rough sawn though it could have.

It is made by the Roseburg mill in Roseburg , Oregon.

I used Porter Paint primer and Porter Paint Acrylic , the best outside Primer and Paint I have used . Been on ten years , no discernible degrading of the paint.

FredD