Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

Learned something about my saw this weekend

Posts

Learned something about my saw this weekend

#1

Learned something about my saw this weekend

Lee Schierer - McKean, PA

>I have a Craftsman Contractor style table saw that is about 20 years old. This weekend I needed to tilt the blade 17 degrees to make some raised panels for a project I'm making. When I went to return the blade to 90 degrees using my digital angle indicator I noted that the saw was very difficult to tilt back and it wouldn't go to 90. It felt like I was going to break something to get the last 2 degrees of tilt out of the blade. I couldn't figure out how the stops could have moved. It took a couple of minutes peering through the various openings with a flashlight, but I finally noticed that the curved arc slot for the blade tilt lock was crammed full on the 90 degree end with sawdust. The accumulated sawdust had compacted so hard that the locking rod could not travel all the way it needed to allow the saw blade to return to the 90 degree position. The washers that rode on the surface would stop the sawdust from escaping as the rod got close to the end of its travel.

It was easy to fix with a slim screw driver to poke out the offending sawdust. Once the sawdust was removed, the saw would easily tilt to minus 2 degrees.

Lee

Re: Learned something about my saw this weekend

#2

Re: Learned something about my saw this weekend

GalenV in Iowa

>WOW! First time in 20 years you cut on a bevel!

I assume the saw is new to you.

I have the same old Sear Craftsman saw for some 30 years and I go through that setup on a regular basis. Mine howls every time you crank the handle. Best solution I have found is using reloading spray case lub on the threaded rods for both angle and lowering rods. Spray never worked for reloading anyway. Saw dust does not seem to stick as bad.

Some day before I die I may buy a real new saw. But then again I probably would not know how to use a good one.

Galen

Re: Learned something about my saw this weekend

#3

Saw is not new to me.

Lee Schierer - McKean, PA

>No actually I've had the saw for 20+ years and I cut bevels all the time. It's just gotten harder and harder to get the blade back to 90 and now I know why. It has nothing to do with dust on the screw thread this is the locking lever that is on the front of the saw and the arced groove it travels in on both trunnions front and rear. My screw threads were pretty clean.

Lee

Re: Learned something about my saw this weekend

#4

Re: Saw is not new to me.

Bricofleur

>Thanks for the lesson Lee. I should bend on my knees to check this out too.

Best,

Serge

www.atelierdubricoleur.spaces.live.com

Re: Learned something about my saw this weekend

#5

I hear ya Lee

Tim Greif - West of Chicago

>There's just certain things about old tools that take you forever to discover. A couple years ago, my old Craftsman RAS that I bought new in '77 started squealing like the dickens on startup and shutdown. I figured the bearings were going and I was destined for an expensive repair. (I'm one of the few people that actually like a RAS and would not be without one) I decided to disassemble the motor housing to have a look. The motor brake is a friction thingy and was so crusted with packed sawdust, it's a wonder the thing worked at all. I blew out what I felt was at least half a motor housing volume of sawdust, did a little lube job and it was like having a new motor.

For such an abused old tool, it refuses to die. I just wish it hadn't taken me over 25 years to discover negative hook blades for it. Now I feel old.

Re: Learned something about my saw this weekend

#6

Re: I hear ya Lee

Fred Davis

>I am glad you discovered negative hook blades for your RAS before you lost some fingers.

It's a miracle more people don't hurt theirselves using tablesaw blades on their RAS.

FredD

Re: Learned something about my saw this weekend

#7

I hear ya too Tim

Bricofleur

>Thanks for the tip Tim.

I have the same RAS (or almost) and I will blow some air before hearing the singing dust.

Best,

Serge

www.atelierdubricoleur.spaces.live.com


img