Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

"Art Project" table

Posts

"Art Project" table

#1

"Art Project" table

Bill Tindall, E.TN

>This table started out to be a table for the porch. We eat breakfast out here when it gets about 50 degrees. Reminds me of camping if its cold, that's a good thing.

Well it turned into an art project and will wind up in daughter's house. It is white oak and finished natural with Target EM 9300 Urethane Polycarbonate finish (sprayed). It is a water white non-yellowing indoor/outdoor finish (its was supposed to go out doors).

Re: "Art Project" table

#4

Thanks......

Bill Tindall, E.TN

>to all the people at Wood Central that offered help in design.

Re: "Art Project" table

#5

Re: "Art Project" table - Oooo!!!

Ray Carson - Lawrenceville, NJ

>That's mighty purdy Bill. I really like the fan effect on the top and how well the grain appears to be book-matched.

Very nice!!

Ray

Re: "Art Project" table

#7

Re: It is book matched - Umm da?

Ray Carson - Lawrenceville, NJ

>Hey Bill,

I guess that was a dumb thing to say wasn't it. :-) Honestly, I just thought you did a REALLY good job of finding matching pieces.

How did you achieve the book matched top? Is it veneer or is it thicker stock re-sawn into halves. How thick is the center pieces forming the "fan"?

Regardless, I love the white oak. The legs are nicely done too.

Ray

Re: "Art Project" table

#8

Nice!

Tony - Memphis

>Looks deceptively simple, but I know it wasn't/isn't. Really nice work Bill. Nice wood too.

Tony

Re: "Art Project" table

#9

Re: "Art Project" table

Barry Irby

>That's really nice Bill. Obviously you should have done like norm and made two of them. Now you have start over and make one for yourself. Flattering that your daughter took it away from you.

A question, are the legs curved? Inside and out or just inside? Or do I need to adjust my monitor again?

Re: "Art Project" table

#10

How book match was done

Bill Tindall, E.TN

>First I planed a quartered board that had flake that arced. Then I laid the pattern pieces on the board to arrange the flakes to flare out as you see them. After cutting out the pattern piece I split it with band saw. Fitting it all together was interesting. The inset top is about 1/2" thick

Re: "Art Project" table

#12

Alan Young

I think that is an innovative design.

Alan Young

>The fan motif is a commonplace feature in furniture but you have displayed it a fresh and attractive setting. And as Tony said- a more complicated piece to execute than might appear. Bravo.

Alan

Re: "Art Project" table

#13

Re: How book match was done - Thanks Bill.

Ray Carson - Lawrenceville, NJ

>

Re: "Art Project" table

#14

$1,200 at Regis Bernard ?

steve mackay

>

Re: "Art Project" table

#15

Re: Top PIC

Bill White

>That's a winner old man.

Bill

Re: "Art Project" table

#16

Dale Lenz

Re: "Art Project" table

Dale Lenz

>NICE looking table, Bill. Assumed you tendoned the fan pieces into the table's top frame. Did you pin the fan pieces from the bottom or just glue. The table is very "clean" looking, I very much like it.

Re: "Art Project" table

#17

tennons and pins and more assembly details

Bill Tindall, E.TN

>Assembly was a nightmare. Tiny errors multiplied across the spaces between the curved pieces resulted in huge gaps at the ends upon assembly. So, I made an outline of the frame on plywood. Then as I fit the "puzzle" pieces to this frame outline I temporarily braded the pieces in place on the plywood. Upon completion I lay the dry fit frame over the "puzzle" and scribed the frame outline onto the puzzle pieces. Then I cut the tenons and chiseled to the scribe line on each piece. In this way I knew it would all fit perfect upon assembly into the frame. However, I had to loosen the tenons so the puzzle pieces could be slid around after they were set into the frame so as to adjust the small spaces between them. When all was well I permanently braded the pieces to the frame.

Re: "Art Project" table

#18

Re: "Art Project" table

Mike Caldwell

>Very nice work. Congratulations.

Mike

Re: "Art Project" table

#19

Re: Top PIC

HC Sakman --- Victoria,BC. CANADA

>I really like the top Bill, nice job.

Chico...