Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

Cutting hinge mortises in a steel door casing?

Posts

Cutting hinge mortises in a steel door casing?

#1

JL

Cutting hinge mortises in a steel door casing?

JL

>I've been asked to put a "dutch" door in the door for the theatre office. I'd be replacing a hack job done by someone else.

To do it right, I would like to recess the hinges that I add and put some mortises in a steel door casing. Anybody have any ideas as to how to cut them? The steel is maybe 1/8" to 3/16" thick. Cutting the horizontal parts doesn't bother me. I figure I can drill and use a hacksaw to get those. I just don't know about cutting the vertical portions. Any suggestions?

Re: Cutting hinge mortises in a steel door casing?

#2

Re: Cutting hinge mortises in a steel door casing?

George Koch

>If I understand correctly what your intend to do, I would make the cuts with a small (4") hand held grinder with a cutting wheel. Keep in mind that most steel jambs are hollow behind so you will have to attach a filler to the framing, either metal or wood,in order to mount the hinges. George

Re: Cutting hinge mortises in a steel door casing?

#3

JL

Would a Dremel tool work?

JL

>

Re: Cutting hinge mortises in a steel door casing?

#4

Re: Would a Dremel tool work?

George Koch

>I really don't think a dremel tool would be strong enough. Not recommending it, but I have seen those grinder disks mounted on a 1/4" shaft into a trim router motor and used without the base.

Re: Cutting hinge mortises in a steel door casing?

#5

Lee Grindinger

If it's only the casing

Lee Grindinger

>I'd just use a grinder, a hand held 4" (or so) grinder. If you're talking about gaining the whole butt into a steel jamb and casing I'd suggest you surface mount the hinge.

Lee

Re: Cutting hinge mortises in a steel door casing?

#6

Re: Cutting hinge mortises in a steel door casing?

Gary Camp, Bend, oregon

>JL a dremel tool should work fine, use the heavy duty fiber reinforced cutting disks. I just had to make a 5" cut in 1/4 steel, the dremel tool did a fine job. I have repaired broken hinge mounting plates in steel door jambs by countersinking flat head machine screws into the jamb, drilling and tapping the hinge plate and shimming for the thickness of the hinge. The locksmith I use drills a couple of holes in the jamb on each side of the hinge plate and welds the hinge plate back to the jamb. Grind it flush and paint it no one can tell you even worked on it.

glc

Re: Cutting hinge mortises in a steel door casing?

#7

JL

Thanks

JL

>

Re: Cutting hinge mortises in a steel door casing?

#8

Re: Cutting hinge mortises in a steel door casing?

tek,brunswick

>I have some experience with steel door jambs. I worked as a carpenter on commercial work for over 30 yrs. For cutting in a pocket a grinder with a cut off wheel works well. A dremel will work but it is quite slow. A die grinder with a wheel would probably be your best bet. If you use the dremel drilling a line of holes with a 1/16 inch drill bit and then cutting along that line to connect the holes speeds things up a bit. A file or a rotary burr will help clean up the edges. As mentioned before you need to add a backing plate to mount the hinge to. Usually we had the company that supplied our door jambs perform the work. They had the right tools to make the cuts and a wire welder to mount the backing plate. They also had backing plates that were recessed to the right depth for the hinges. Making the jamb look good again is usually a bondo job. They do make half surface mount hinges that do not have to be let in, but do not look as nice. I hope this helps.

Tom