Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Cutting a newel post....the hard way.

Posts

Cutting a newel post....the hard way.

#1

Cutting a newel post....the hard way.

Ray Carson, New Jersey

>Hey everybody,

Been a while since I've posted. I've been busy with school, kids, work, house repairs and WOODWORKING!!! I've sure missed Woodcentral. I'm currnetly working on a corner cabinet for my LCD TV amongst other things. I'll post PICS when it's all done so you all can critique it. LOL.

So...

I've been asked by someone to cut four newel posts to attach to the corners of some kitchen cabinets. They want an effect of a table for the countertop. I love a challenge and I accepted the project.(stupid, stupid, stupid me LOL) Basically I need to cut out 1/4 of a pre-manufactured newel post. The tapered portion is the tricky part.

I have a few ideas of how I can do this. I thought first of building a U-shaped channel of 3/4 MDF, placing it over the blade in the proper location and raising the blade up thru the MDF and then passing the newel thru the channel. This poses one problem. The MDF channel will have to extend a few feet in front of and in back of the saw table. Not the safest method. The extra length has me concerned too with keeping a straight cut.

Second idea was to build a box around the post, securing it in place slighty to keep it from possibly drifting inside and make the cuts I need. Only problem I see with this idea is the corner of the box has now been sacrified and unusable for the three remaining posts.

Third idea is much the same of the second, the only difference being that I cap the top and bottom ends. I don't know if it would matter but the wheels are turning and I'm starting to confuse myself. LOL

I attached a sketch of what my 3rd idea looked like for discussion purposes. (Google SketchUp)

How would you all attempt this? Has anyone done this before?

Ray


img

Re: Cutting a newel post....the hard way.

#2

Re: Cutting a newel post....the hard way.

Ken Romines

>Ray

There are two ways to do what I understand you need:

1. Turn the newel post yourself and use a glue post with newspaper or butcher paper between the pieces, seperate the pieces and finish to match. However, I understand you have prefinished posts to match a cabinet and that is a different problem;

2. Hot glue the post in a box and cut the post in half with a band saw and the thinnest band you can find, then cut one half into quarters and glue one quarter back onto the first half. It leaves a seam on one side but done properly and by turning the seam away from the primary sight line it will pass muster.

3. You can also check with the post maker. A generation ago when I installed cabinets you could order the post with a 1/4 section already cut out.

Good luck

Ken

Re: Cutting a newel post....the hard way.

#3

Here's a way to do it...

Ellis Walentine, Host

>Screw squares of MDF to each end of the newel and centered on it. The squares should be the size of the major diameter of the posts. Make a long enough auxiliary table and fence for your tablesaw -- two eight-foot long pieces of MDF joined in an "L" should do it. Set your fence where it needs to be, raise the blade up through the auxiliary table to the centerline height of the newel, and rip, riding the edges of your squares against the auxiliary table/fence. Rotate the newel 90� to make the second cut.

I also use this technique to rout quadrants or grooves in circular stock.

Ellis

Re: Cutting a newel post....the hard way.

#4

Yes But

Mark Mandell - Gone Round In Jersey

>If he rotates it only 45�, that will give him a "V" cut rather than a square corner notch, no?

Need to remember to fix the post in the jig so that it won't rotate during the cut; serious personal injury lies in wait here. That will take at least 2 screws or nails that are located so that they remain outside of the cut/waste section of the post.

Re: Cutting a newel post....the hard way.

#5

Thanks, Mark

Ellis Walentine, Host

>I meant to add the caveat that you described. And I corrected my 45� brain cramp. :-)

Cheers,

Ellis

Re: Cutting a newel post....the hard way.

#6

Re: Here's a way to do it.....that's about

Ray Carson, New Jersey

>along the lines I was thinking. :-) Pun intended.

The newel post(s) will have a small square section at the top near a ball finial and a large square section at the base. In between are beads and coves and the tapered portion. The square portions have pommels on the corners. The ball is getting cut off for aesthetics. This person doesn't want a ball. Ooy!!

I think I'm on track with what I need to do.

Thanks Ellis.

Ray

Re: Cutting a newel post....the hard way.

#7

Re: Yes but.....gotcha Mark

Ray Carson, New Jersey

>I saw through the 45 comment by Ellis. Ninety degrees is what I need. His advice and yours are the solution to my problem. My PIC I attached was my idea of a jig I'll need to build. Something like it. I definitely need to fix the newel to something in order to cut a 1/4 out of it.

Thanks Mark.

Ray

Re: Cutting a newel post....the hard way.

#8

An Anudder Ting

Mark Mandell - Gone Round In Jersey

>While we're at it.

Since your leg is tapered, your jig will need to be "tapered" as well to keep the cut at or near the center line of the leg. Remember, the center line of the post must run parallel with the fence and blade. Hence the "block" on the small end will be larger than what you use on the big end by the same amount as the amount of the taper. Measure the leg's diameter and subtract the small from the large. That should be the amount to increase the larger block since you are making a cut of the radius of the leg.

I would consider cutting a mortice in each end-block to take both ends of the leg. This, in addition to the two pins/nails/screws will do a better job of supporting the workpiece which, except for the very end of the largest section, is going to be riding on air.

Re: Cutting a newel post....the hard way.

#9

OOOPS

Mark Mandell - Gone Round In Jersey

>Forgot to mention that the center line of the leg must remain parallel to BOTH the fence and the table top.

[Yeah, I suck a three dimensional chess as well]

Re: Cutting a newel post....the hard way.

#10

Re: Cutting a newel post....the hard way.

Barry Irby

>Ellis and Mark have explained it very well. But that never stopped me from throwing in my 2 cents before, so why now?

Build a jig that supports the posts off the square sections so that the center line is parallel to the table and the fence. You can fasten the bottom end through the end in such a way that the screws don't get into the saw blade. Use the ball as a waste block to fasten the top of the post into the jig, again so that the screws don't get into the blade. Then cut the remainder of the ball off and the screw holes go with it.

Or, how about a different approach? Build the jig to attach to the 1/4 you are going to cut out. Then make the two cuts and the waste stays in the jig, along with the attachment holes.