Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

Leveling off shellac

Posts

Leveling off shellac

#1

Leveling off shellac

Barry Rubenstein

>I'm at the end of a jewelry box project and applied about 5 coats of shellac with a brush. Needless to say the shellac finish has dips and waves (not too severe) that I would like to level off. It's been about a week since the last coat and the finish seems hard enough to be "leveled off". With this situation in the past I've used a very fine sandpaper with a little water to level it all off. Once I worked at it too much and went through all coats of shellac; had to start all over again.

Any suggestion/experience with this situation? What has anyone used to "finish the finish"?

Re: Leveling off shellac

#2

Re: Leveling off shellac *LINK*

Dick Coers

>Use mineral spirits/paint thinner for the lubricant. I use 320 paper to cut it all flat, then switch to Abralon to bring it to the sheen I want. If you go to 4000 is will almost looked like you buffed it. Very high gloss.


abralon

Re: Leveling off shellac

#3

Re: Leveling off shellac

George@Colonel's Workshop-Havertown PA

>Good Evening Barry,

I've used water as well as naptha/oil mix. Both work. I try to level after the second or third shellac application, and then re-apply more shellac. However, I use a soft rag to wipe on the Seal Coat application to keep the "coat" thin as possible. I also prefer to use 4/0 steel wool during final rub outs, and clean each time with naptha and a soft cloth/paper towel. When the naptha flashes off, you can see how well your coverage is progressing.

George

Re: Leveling off shellac

#4

Re: Leveling off shellac

Jerry Gibbs

>just curious. if you are building up the shellac to level off, why do you want to keep the coats as thin as possible? Jerry Gibbs

Re: Leveling off shellac

#5

Re: Leveling off shellac

Barry Irby

>I have used what I think is the "classic" method. Paraffin oil, pumice, then rotten stone, both rubbed with felt blocks. Different blocks for the different grades of pumice and rotten stone. It did a great job, but was time consuming and a bit messy.

I also stumbled on the idea of buying Zinser Bullseye Shellac in spray cans and using it as a top coat over my built up coats. I scrapped (with a card scraper), Sanded a bit with 320 and sprayed on a top coat. The spray stuff is expensive, but a $5 or $6 can will more than do a jewelry box and it goes on much smoother than I can do it with a brush.

The spray can worked so well, I used it start to finish on several jewelry boxes. Very little rub out/touch up required.

(I'm a reluctant finisher and hate buying a $40 brush to just see if it really is better than a chip brush. It killed me to buy about $40 worth of paraffin oil and pumice, etc.)

Re: Leveling off shellac

#6

Re: Leveling off shellac

George@Colonel's Workshop-Havertown PA

>Good Morning Jerry,

I try to maximize uniformity of thickness early on--keep the finish even as it builds.

George

Re: Leveling off shellac

#7

Re: Leveling off shellac

Dave Bair, Eaton Rapids, MI

>Try a product called "Wool-Lube". It feels like liquid soap and is meant to be used with 0000 steel wool. I've found it can be diluted with water (at least 50% to use less product) and works well with 400 and higher grit sand paper.

Re: Leveling off shellac

#8

Re: Leveling off shellac

gary peterson

>after you "build" your shellac finish , use a cut portion as a final coat, it will dissolve the last coat, meld a little bit, and should produce a nice smooth finish.