Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

OT: Glue Applicators

Posts

OT: Glue Applicators

#1

Dominic in Bucks County PA

OT: Glue Applicators

Dominic in Bucks County PA

>I've been looking for a specific type of glue applicator and was wondering if anyone here could help me.

This is for a project at my day job. I need to apply a strip of clear liquid glue primer to an area that is 3/4" wide. I was thinking of an applicator that had a foam head and the body was hollow and could be filled with the primer. The method we're using now is to use an acid brush. That's messy and not very accurate.

I've tried searching McMaster Carr, Grainger, and even went to Michael's Crafts. But I've had no luck.

Any help?

Thanks,

Dominic

Re: OT: Glue Applicators

#2

Re: OT: Glue Applicators *LINK*

GalenV in Iowa

>There is glue bottle rollers from Woodworkers Supply (Woodworker.com) Page 147 in my older 2008 catalog.

Biscuit glue bottles with or without a roller attachment should be available if that is what you are talking about.

Similar to the link from Peachtree Woodworking.


http://www.ptreeusa.com/glue_products.htm

Re: OT: Glue Applicators

#3

Re: OT: Glue Applicators

Bricofleur

>I believe the glue needle injector from this website would work fine too. I bought one from Lee Valley after seing Doug Stowe using it in tight areas. Great for precise work.

Best,

Serge


img

Re: OT: Glue Applicators

#4

Thanks you guys but

Dominic in Buck's County PA

>while I appreciate your help they are really not what I was looking for.

For one, this is not really glue. If you re-read my original post you would see it's a liquid primer. It has the consistency of water.

Therefore a needle applicator would be VERY messy (and not accurate). While the foam roller on the glue bottle from PeachTree would be too wide.

I'm looking for a clear bottle with a top that has a piece of foam in it (picture a magic marker with a refillable body). This would be IDEAL for this application. It would allow the worker to apply an even strip of the primer with ease. As a kid we used to get glue for crafts in this type of bottle. I find it hard to believe that no one carries something like it.

Re: OT: Glue Applicators

#5

Re: Thanks you guys but

Bricofleur

>Try a shoe store or manufacturer. I remember having seen this kind of applicator to spread stain and shoe shine on shoes. Maybe a shoe repair shop too. You never know!

Best,

Serge

Re: OT: Glue Applicators

#6

Polish applicator!

Dominic in Buck's County PA

>Yeah, just like a shoe polish applicator! Good call!

Re: OT: Glue Applicators

#7

Jim DeLaney, Austintown, Ohio

Re: Polish applicator!

Jim DeLaney, Austintown, Ohio

>Dom,

Office supply stores have something like what you want. It's a 'squeeze tube' with a flat foam head on it. It's intended for moistening envelopes. Probably cost you less than a buck.

Jim D.

Re: OT: Glue Applicators

#8

Try Office Max

Lee Schierer - McKean, PA

>Look at an office supply place for an envelope moistener. They have a small clear bottle that gets filled with water and a foam tip for gluing shut envelopes in office mailings.

Lee

Re: OT: Glue Applicators

#10

Dominic in Bucks County PA

Thanks Jim!

Dominic in Bucks County PA

>

Jim,

That's the ticket! You were beat by Lee (who suggested the same thing)by only 2 minutes.

Thanks to all who supplied suggestions and input. I knew I could count on you guys!

See ya around,

Dominic

Re: OT: Glue Applicators

#11

Dominic in Bucks County PA

Follow up!

Dominic in Bucks County PA

>I went to Office max during lunch and bought some of these "envelope moisteners" then tried then out. They work PERFECTLY! So I'm one happy camper.

Thanks again!

Re: OT: Glue Applicators

#12

What did I win?

Lee Schierer - McKean, PA

>And when can I expect UPS to deliver it? :)

Glad to have helped.

Lee

Re: OT: Glue Applicators

#13

Re: Follow up!

GalenV in Iowa

>Sounds like you qualify for a BIG bonus if it improved efficiency at your day job!

Since you did not say what the primer was I had thoughts of it disolving the plastic bottle or foam.

Wonder if it would apply Myland friction polish to a turning so all I need is the paper towel to polish?

Galen

Re: OT: Glue Applicators

#14

Re: OT: Glue Applicators

Andy Lincoln,in Dearborn MI

>Dominic,

After reading thru this thread I was wondering if the primer you are applying is 3m VHB primer or similar???What ,if any adverse affects on th ebottle/applicator???we use alot of this and the application method sounds perfect,

Andy

Re: OT: Glue Applicators

#15

Re: Follow up!

Dominic in Buck's County PA

>It's a primer for transfer tape adhesive. It's a 3M product called 468MP. We stick it to 0.040 PCV and then knife cut out the parts. You then end up with a piece of PVC, cut to the exact size you need. All you do it then peel the transfer tape off and expose the glue. In order to get maximum strength from the transfer adhesive, you need to apply this primer to the substrate.

The envelope moistener bottle gets filled with a small amount of the primer and the user just "draws" between lines marked out on the substrate. The lines also help the user to position the PVC piece correctly when applying it.

This little trick ends up saving over 75% of the labor time over the old method (which involved using vinyl adhesive applied with a brush!)

Yeah, I'm pretty proud of it.