Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

Cutting narrow slices

Posts

Cutting narrow slices

#1

Cutting narrow slices

BrianA

>I need to cut about 80LF of 1/4" x3/4" strips from a piece of Oak for some trim. I do not like to use my push stick (metal) between the blade and the fence and dislike when the narrow piece shoots back like cupids arrow. I thought I saw a jig for ripping narrow pieces and keeping them uniform. I cannot find one. I have seen a push stick that you build to fit over the fence. That would be my second choice. Any ideas?

Thanks

Brian

Re: Cutting narrow slices

#2

Re: Cutting narrow slices *LINK*

Bill Roland (Mt Juliet, TN)

>Here is a video of one fixture.


Video

Re: Cutting narrow slices

#3

Bandsaw

Thomas Skaggs, Foothills of Mount Level

>The bandsaw can be set up to do that well and much more safely. Featherboards are helpful.

Tom

Re: Cutting narrow slices

#4

Re: Cutting narrow slices

Ellis Walentine, Host

>When I see questions like this, my editorial instinct (and liability instinct) is to pass, because I don't use a blade guard or splitter for this operation, and a lot of people think this is absolute heresy. I'm just telling you what works for me, and I wouldn't pass it along if I didn't think it was safe. That said, my disclaimer is that nothing is completely safe, and it's up to you to decide whether you want to try this or not. Your safety is your business.

To me, this is a straightforward ripping operation, no jigs or bells or whistles. The secret is in the push stick, or push block might be a better word for it. The style you want to use is shaped like a boot, with a tall handle that keeps your hand far from the blade.



Raise the blade about 1/4" or less above the thickness of the board, set the fence 1/4" from the blade, and rip your board normally. (I wouldn't try this with a board that is narrower that several inches wide to begin with, and I wouldn't recommend ripping strips thinner than 1/4" or so.) When you get down to the last foot or so of your rip, hook the push block onto the back of the strip, keeping the side of the push block firmly against the fence. Apply forward and downward pressure on the strip of wood by pushing on the handle of the push block. Do not attempt to hold the main part of the board with your left hand, just let the push block do the work, and follow through until you've pushed it past the blade. On the first cut, the blade will cut a kerf into the bottom edge of your push block. That's normal; these things are meant to be sacrificed.

If you are concerned about keeping the push block tight and flat against the fence, you can make a push stick that straddles the fence. If you have a riving knife on your saw, you can use it, but that means you need a push stick/block that is less than 1/4" thick to clear the riving knife. To me that's dicier than the straightforward method I described.

There is a push device called a Grrripper that has rubber pads to hold the piece down on the table. I've heard people recommend this tool for ripping thin strips, but I can't speak from experience.

Ellis Walentine, Host

Re: Cutting narrow slices

#5

Re: Cutting narrow slices

Barry Irby

>You did not say how long your pieces need to be. Depending on that I would:

Short pieces, up to three or four feet: Use a scrap board About two to six inches wide and about the length of your pieces and the same thickness. (3/4" ?) Tack or glue a pusher piece on the rear that sticks out toward the blade a 1/4". Put a top on it that stick out toward the blade about a 1/4". This creates a "boxed notch" or "housing" on the edge that is the size of the strip you want.

Set your fence so that the original scrap is a 1/4" from the blade. Insert your stock into the notch and rip off the strip. Over and over until your stock is too narrow for comfort. With this setup, rather than the one in the video posted above, you don't have to change the fence each time. The housing does a good job in holding the strip until you push it past the saw. If you are uncomfortable, you could use some double stick tape in the housing, but my experience is that the tape is only good for a couple of pieces and becomes a bit of a PITA and is unnecessary.

I have used a jig like this many times to rip strips for splines. Once you fiddle the fence into the right position you can cut as many as you need without changing anything and those are about 1/8" thick and have to be very accurate.

IF my strips were longer, I would either cut them on a bandsaw or the TS. Bandsaw would be safer. But I don't have a fence for mine and can not free hand rip any thing near a glue line rip. I would have to joint the stock, draw a line, rip it, joint the stock and rip again, etc. Then I would have to run the strips through the planer or drum sander to clean up the other side. With a good blade on the TS I could rip them and probably use them. Maybe lightly sand them. With longer pieces I would not hesitate to rip them on the saw without a jig. I stand where I could catch the thin strips and pull them through.

Re: Cutting narrow slices

#6

I agree with this approach

Bruce, a MN Galoot

>and would add only one thing:

make sure you have an outfeed table big enough to handle the piece you're cutting so you won't have to pay any attention to it. That way you can give all your attention to feeding the board and keeping your hand safe.

I've cut hundreds of feet (maybe thousands - I've lost track over the last 45 years) doing exactly this, including all the strips for a cedar strip canoe. No problem in the slightest, ever.

Bruce

Re: Cutting narrow slices

#7

Re: Cutting narrow slices

Chris Friesen

>"If you have a riving knife on your saw, you can use it, but that means you need a push stick/block that is less than 1/4" thick to clear the riving knife."

A true riving knife is lower than the blade itself, so the kerf cut by the blade should ride over the riving knife just fine. A splitter, on the other hand, will cause the problem you mentioned.

Re: Cutting narrow slices

#8

a very easy task

Bill Tindall, E.TN

>This task would take but a few minutes in my shop.

1. Make a wooden push stick 1/4" thick.

2. Get a 7 1/2 or 8" diameter 40T thin kerf combination blade.

3. Set saw up for 1/4" between blade and rip fence.

4. Joint edge of stock piece.

5. Rip a strip.

6. Joint stock piece.

7 rip a strip.

8. repeat

It was not my idea to use these small blades on a 10" saw. I was at IWF years ago and someone was demoing their magnetic feather board by ripping 1/8" strips. I was amazed at how little resistance force their blade was making during their cuts. They had an easy task controling the stock piece and the strips. So I got a similar blade (CMT in this case but now I have tried several others) and found ripping thin strips to be effortless.

I would not hesitate to do it with a 10" combination or rip blade. But, there would be more cutting resistance so that keeping the stock piece under control would be more of an issue.

Re: Cutting narrow slices

#9

important PS

Bill Tindall, E.TN

>Do not raise the blade more than just a bit more than 3/4"

Re: Cutting narrow slices

#10

Also my method

Lee Schierer - McKean, PA

>I've used an identical method to cut thin strips. I've actually cut strips as thin as 1/8" using the method Barry describes. You can probably go thinner than that if you wanted, but will waste a lot of wood in saw kerfs. The strips are very consistent in thickness and the operation goes very quickly and most importantly it is safe. I made a diffuser for a wall mounted humidifier at church that needed several dozen 1/4 x 3/4 x 18" strips.

Lee

Re: Cutting narrow slices

#11

Re: Cutting narrow slices

Larry Marker in Alabama

>I use a GrrRipper.

Larry

Re: Cutting narrow slices

#12

Re: Thin rip jig *LINK*

pecker

>80lf at 1/4" is 10 rips on an 8ft board, removing only 2.5" total (plus kerfs)from a wider board.

You could easy use (or make) a Rockler Thin Rip Jig for this...your pieces end up on the non-fence side of the blade.


img

http://www.rockler.com/product.cfm?page=18056&filt

Re: Cutting narrow slices

#13

Re: Cutting narrow slices

BrianA

>Thanks everyone I think I can do it safely now.

Brian

Re: Cutting narrow slices

#14

Re: Cutting narrow slices

Brian in Brighton

>I made a push stick that looks more like a saw handle, with a notch on the bottom rear to push the wood, that allows me to push both sides of the material completely thru the blade. It holds both sides and since it's made of wood it is not a problem to cut thru it.

Brian in Brighton