Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Lockset Jig - Redux

Posts

Lockset Jig - Redux

#1

Lockset Jig - Redux

Jerry Nicholson

>Several days I asked about where to buy a lockset jig for my 7 new mahogany panel doors and was pointed to the Borg. Lowes did indeed have the Dewalt lockset installation jig in stock. Several people also pointed out that the the old way, ie use a paper template, would work just as well. Being stubborn and lazy, I bought the Dewalt. It carefully guided me in drilling the latch hole and the knob hole way off center. I came really close to ruining the door but it came out OK. This Dewalt jig is a piece of junk and I probably could have bought something better at Harbor Freight! On the other hand, my Veritas Small Router Plane really worked great on the mortise for the face plate of the latch.

Jerry

Re: Lockset Jig - Redux

#2

Re: Lockset Jig - Redux

Fred Davis

>Sorry about the door , Jerry, but you could save yourself sone pain and money , by either going to a tool rental or a Hardware store that rents tools and get thier jig on a rental basis.

I wouldn't be surprised if it is a Kwikset jig.

FredD

Re: Lockset Jig - Redux

#3

Re: Lockset Jig - Redux

Jerry Nicholson

>The door has survived, in spite of my best (worst?) efforts. The thing is heavy and I don't have much muscle anymore so I will probably ding it sometime while moving it into position for the next operation. The problem with renting is that I am really slow and only have room to work on one or two doors at a time.

Re: Lockset Jig - Redux

#4

Re: Lockset Jig - Redux

Barry Irby

>Summer a year ago I replaced all the doors in a rental property for a friend. I bought a plastic jig from the borg. It was pitiful. Sort of rubbery and not accurate at all. It was clear it was not going to do the job and would ruin a door or two before it was over.

I made my own by ripping a strip the thickness of the door and gluing and nailing a piece of 1/2" plywood on both sides. Before gluing them on I drilled holes in them to match the location of the lock set. I drilled a hole in the edge strip that lined up with the center of the holes and the center of the door. I marked the height of the locks on the edge of the door. This became the center of the keeper. So you would slip this guide over the edge of the door and drive a screw through the hole in the jig into the hole in the edge of the door. I also clamped the template to the door with a couple of those Quick Grip bar clamps. Then I drilled from both sides.

Remove that contraption and using a 7/8" drill, drill the hole in from the edge using the screw hole as a center.

I made two templates of half inch plywood for the recess for the strike and keeper and used a router to cut the recesses.

Almost took longer to explain this than to make the templates. Unfortunately, they were so easy to make and I do this so rarely, I through them away or I would take a picture for you.

Re: Lockset Jig - Redux

#5

Re: Lockset Jig - Redux

Jerry Nicholson

>I might build my own lockset jig and a latch plate mortise jig wouldn't be difficult. I made my hinge mortise jig from a 2 x 4 jointed on two sides and some plywood. Many years ago, before I had router bits with pilot bearings, I made a hinge mortise jig by creating a box holding the entire router base. Crude, but it did the job.

The most critical thing to me is the hole in the edge for the latch. The Dewalt jig came with a 1 inch hole saw but that is way bigger then necessary for my Schlage locksets. 7/8 bored right straight in would be just right. Last night I was thinking about drilling the pilot hole using a dowling jig and maybe replacing the pilot drill in a 7/8 hole saw with a rod. That way the hole saw should follow the pilot hole right straight in.

Re: Lockset Jig - Redux

#6

Re: Lockset Jig - Redux

Barry Irby

>Jerry, I have done scores of Schlage locks over the years. (I used to be a builder and trimmed out dozens of houses). the quality of the locks has come down. The ones I have done recently has not been as good as they used to be.

Drilling the hole in the edge of the door is not nearly as critical as it appears. There is plenty of play or "slop" in the setup to allow for misaligning the holes. I've done a bunch with spade bits and a bunch more with auger bits.

If you want an alignment tool, you could make a guide out of a piece of 2X4 (hardwood would be more durable). Rip a piece the thickness of your door. Drill a hole through it, carefully centered on the edge and perpendicular. (Easy with Drill press). Attach 1/4 or 1/2" plywood to both edges so it will slip over the edge of the door. To align it, you can start the hole with a spade bit, auger, or a forstner bit. Then put the guide in place and use a piece of dowel or the auger or forstner bit to align it with the hole and clamp it to the door. Drill the rest of the way with the auger or with a hole saw.

Re: Lockset Jig - Redux

#7

Re: Lockset Jig - Redux

Jerry Nicholson

>I'm reusing the existing locksets. They might be as old as the house (43 years) but they still look pretty good and work OK so I don't see any need to replace them.

Jerry