Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Poplar expansion

Posts

Poplar expansion

#1

Poplar expansion

Joe Grittani

>Greetings!

I poked around the archives a bit and couldn't find anything specific regarding my question.

I'm getting involved in a project that involves frame and panel construction. The material is poplar. I tried using the "Sagulator" but couldn't provide the information required re: moisture, etc.

The wood is kiln dried and has been cut to rough size for about a year. The panels are 11 1/2 to 12 1/2" wide and 3/4" thick. They've been sticker-stacked and stored in the heated area where they'll be installed. They'll be planed down to 1/2" (taking equal amounts off of both sides) thickness and rabbeted down to 1/4" to fit into grooves in the stiles and rails.

I'm assuming these panels are at their smallest dimension and am trying to figure out how much expansion room I need to allow across their width. We're talking southern Ohio climate and no air conditioning in the summer.

Thanks for your thoughts.

Joe Grits

Re: Poplar expansion

#2

Re: Poplar expansion *LINK*

Mark Mandell - Gone Round In Jersey

>Put 10% MC in the calculator and you'll be fine with the answer. KD will come out(depending on the program)around 5-6% and then soak up some to stabilize with the ambient. From your description, EMC in your area is going to be near 10%, and the amount of variance from that will be irrelevant for your needs.

If you like doing the calc by hand look up your wood in the USDA Forest Service Handbook at the link, and take it from there.


Fed Forest Product s Handbook

Re: Poplar expansion

#3

Yellow/tulip poplar or popular/aspen/cottonwood?

John K Jordan

>

Re: Poplar expansion

#4

Re: Yellow/tulip poplar or popular/aspen/cottonwoo

Joe Grittani

>I'm ashamed to admit I'm not sure. It's what hardwood dealers around here (Ohio) sell as poplar. It's not from the borg.

I assume it's yellow poplar.

Joe

Re: Poplar expansion

#5

That is usually yellow/tulip poplar...

John in NM

>I don't know as I've ever seen members of the populous genus for sale in a hardwood yard, though my neighbor has it as ceiling material in his house (aspen), so it must be readily available from building suppliers. The stuff I've always seen sold as poplar at hardwoods suppliers is always tulip or yellow poplar.

As to shrinkage, I usually assume about 1/8" per 12" width and never had any problems. I also sometimes use foam backing rod if its small enough to fit in the groove, or cut sections of it if not. I think I've rarely if ever had wood from the lumber yard not shrink considerably over the first year or so of use - but then I live in a very dry climate.

Re: Poplar expansion

#6

To be on the safe side...

Ellis Walentine, Host

>... I'd leave 1/8" headroom in both stile grooves. You don't need to leave any in the rail grooves.

Poplar is a pretty stable wood, with 1.9% shrinkage/expansion for flatsawn stock in the MC range of 6% - 12%. The radial movement is considerably less. From your description, I think you're right about the wood being at (or near)its smallest dimension right now, but it may not be as dry as 6%. In your climate in the summer, with no air conditioning, I'd expect the moisture content to increase to somewhere around 12%, so you want to leave room for the full 1.9% expansion, or about .23" per 12" of width, less for quartersawn.

Realistically, since your wood has been acclimating for so long, it has probably gone through the largest dimensional changes it will ever undergo, which is always in the first year. If you were a gambling man, you might leave a little less headroom because of this.

Ellis Walentine, Host

Re: Poplar expansion

#7

Re: To be on the safe side...

Joe Grittani

>Thanks to all. And when it comes to this stuff, Ellis, I'm not a gambling man. I'll go for 1/8"+ on each side.

Joe