Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Polycarbonate or similar in Display Case

Posts

Polycarbonate or similar in Display Case

#1

Polycarbonate or similar in Display Case

Glenn Madsen near San Francisco

>Funny how things work. I was going to post a question on glazing a display cabinet with polycarbonate or similar materials.

Has anyone done this with success?

I'm helping a library with some cabinets and cases, and curious about the glazing. Only minor glass experience, and no desire to use glass in this application.

The shop is a woodworker's shop. No glass tools. No glaziers' experience.

Ideas?

Re: Polycarbonate or similar in Display Case

#2

Re: Polycarbonate or similar in Display Case

Fred Davis

>Glenn,

Polycaronate and PlexiGlas will work, but...... their scratch resistance is next to zero, hence the use of glass.

You don't need to be a Glazier, just know one.

Think long term on scratching and how long it took you to make the case. Plus acryillic glazing ,like Plexiglas cost's more then glass.

FredD

Re: Polycarbonate or similar in Display Case

#3

Re: Polycarbonate or similar in Display Case

Clint Searl, at the base of Haycock Mtn

>It'll never break, but it does scratch easily. A less expensive material that's just as good in your application is plexiglass, IMO. Easier to work, also.

Clint

Re: Polycarbonate or similar in Display Case

#4

The polycarbonate is the easiest to scratch,

Keith Newton------WebKitFormBoundaryV6MZb+tiOpocz6

>but is tougher to cut and break.

If you use plexiglas, you should consider SAR, scratch and abrasion resistant. It will hold up better, and is easier to cut.

If you use polycarbonate, be sure to use a really sharp clean blade, with a zero clearance plate, and feed fast enough to not burn and get side welding on the tooth, or it will kick your butt quicker than anything.

Re: Polycarbonate or similar in Display Case

#5

Re: The polycarbonate is the easiest to scratch,

Pete in Holland, MI

>Would use Acrylic over Polycarb for your application. Acrylic is stiffer and pretty tough for the application. Polycarb is a little softer and more apt to sag/warp over time. Polycarb is also much more expensive than Acrylic.

If you are making a display case for a school, either of the plastics will be fine. If it is glass, you should use tempered.

Pete

Re: Polycarbonate or similar in Display Case

#6

Re: Follow on questions, and a few additionals

Glenn Madsen near San Francisco

>Thanks, folks, so far the info has been valuable.

This project is for a family history library, mostly used by adults later in their years, but sometimes kids and general public are there. Not all of the staff are as adept with their motor skills as they might have been in their earlier years.

Fancy is less important than durable, and affordable, workable with woodworker tools and available to the market are important. There's not a ton of money budgeted for fancy displays.

Acrylic sounds reasonable. What sort of supplier sources this, other than TAP Plastics at retail? I estimate I'd need the equivalent of perhaps 6 or 8 sheets (4'x8') to do what we discussed earlier this week.

Thanks again for your assistance! Expert help is always appreciated.

Re: Polycarbonate or similar in Display Case

#7

Re: Follow on questions, and a few additionals

Pete in Holland, MI

>Check the internet or yellow pages for your area. The stuff is big & heavy. You might find it cheap some place, but getting it to you will be an issue. Check with a local machine shop that specializes in machine building. They can probably hook you up with their sources.

Also, with either acrylic or poly-carb, don't sand the edges. Unless you're in the best situation, it'll only make a mess. Use a block plane instead to break the corners.

Good luck.