Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Joining with a tablesgaw

Posts

Joining with a tablesgaw

#1

Joining with a tablesgaw

pacsalot

>When I surface the edge of a board by ripping on my tablesaw, I get a .02 inch variation from the middle of the board and the ends of the board. This happens even though I use a fence. This does not sound like much but when I try to join two boards, who's edges have been surfaced in this manner, I get a .04 inch gap between the boards. Just as a reference, 1/32 inch is equal to 0.03125. My joiner is out of commission. And the boards are not wide enough to join them with a router. Does anyone have any suggestions how to get a straight edge on the boards?

Re: Joining with a tablesgaw

#2

Re: Joining with a table saw

Barry Irby

>I can't answer your question about how to get them even straighter on a table saw. Perhaps a better "glue line" blade would do a better job, depending on the quality of your blade now.

There are some who believe a slight "hollow" in the joint is acceptable. Not sure how much that would be. I think it would also depend on how many boards you are joining. If you are gluing up two or three and you can easily pull them up with gentle clamp pressure you are probably OK. ("OK" being a highly scientific term of art)

It would seem that the more pieces you glued up, the more "error" you would accumulate and the straighter you would want them to be. I just don't know what the limits are.

Another approach might be to glue us several apples of two or three boards and then rip and edge on each panel and then glue up the sub assemblies. Or, maybe by that time they would be wide enough to work some magic with your router or, heaven forbid, a hand plane. (I have heard this used to be quite standard, but not for me.)

Re: Joining with a tablesgaw

#3

Alignment

Lee Schierer - McKean, PA

>You need to check the alignment of your saw. Start by checking the alignment of the blade to the miter gauge slot. Then check the alignment of the fence to the same miter gauge slot. You should be able to adjust your saw to within .005 or closer with a cheap dial indicator. The fence should be parallel to the miter gauge slot. Worst case the back of the fence behind the blade should tail away a few thousandths of an inch. Once your saw is aligned you get better quality cuts.

You didn't say how long these boards are. The longer the board, the longer the fence you need in front of the blade. You can buy a piece of square aluminum tubing from the local Borg and make a runner that is 6' long to help guide your boards. If the side of the board against the fence isn't straight to start you won't easily get a straight rip cut. Again this aluminum tube can be used as a guide and you can place shims held with tape between the aluminum tube and the back side of your board. When you make a cur slide the board and the tube across the table at the same time, keeping the tube to tight to the fence and the board against teh shims and against the tube.

Lee

Re: Joining with a tablesgaw

#4

Re: Joining with a tablesgaw

Larry Marker in Alabama

>Last time I had that problem, it was due to a cheap blade. Replacing it with a quality carbide blade fixed it.

Larry

Re: Joining with a tablesgaw

#5

Yup!

Bruce, a MN Galoot

>When I can't get a straight cut, it's the saw telling me it's time to get the blade sharpened. Mine went off to the sharpener on Friday.

bruce

Re: Joining with a tablesgaw

#6

Dale Lenz

Re: As Barry, suggested...

Dale Lenz

>use a hand plane. Maybe a better statement is to learn to use a hand plane. Been making shaving since July, 1982, not as quick as a jointer or TS but I believe a well shot hand plane joint is superior. Enough said, good luck

Re: Joining with a tablesgaw

#7

Hand planing for edge joining is a piece of cake.

John E in SC

>Even for a relatively inexperienced hand-tooler like me. I don't have a decent joiner (just a benchtop model), but you can put the two boards you're wanting to join side-by-side, edges up, and plane with a decent hand plane until you get a good shaving from the full length of both boards, then just open them up and the edges will match wonderfully well. Takes a little elbow grease, but like me, can get you by until you get your joiner fixed.