Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

French Cleat Material

Posts

French Cleat Material

#1

French Cleat Material

Robby Wright

>Hi, All -

As part of my shop reorganization and general fix-up, I am in the process of building a pair of new tool cabinets that will be hung over my workbench. I would like to use French cleats to mount the cabinets to the wall. I would like to keep the cleats as thin as possible. I expect the cabinets to weigh a lot when full.

This brings me to my question: Does anybody see any problem with using 1/2" Baltic Birch plywood for the cleats? I have a bunch of leftover scraps from the building of the cabinets. Because of the multiple directions of the layers of the plywood, I would expect the plywood to hold up under enormous loads and to not have to worry over the wood splitting.

Thanks for your help.

Robby Wright

San Marcos, CA

Re: French Cleat Material

#2

One Opinion

Mark Mandell - Gone Round In Jersey

>If you're looking at real weight, bypass the plywood and go with steel basin cleats (cheap at any big box store plumbing section). I use them to mount cabinets to the concrete walls of my shop without any problem. I also point out that in your proposed application, you would be putting all the shear force along the lamination lines which is the weakest part of the plywood. For general cabinetry, you're likely to be fine with the wood, but I would be uncomfortable about heavy loads.

My take, YMMV |;-}}}

Re: French Cleat Material

#3

Just about any material

Mike Farinella

>will work good as long as you attach to the studs. Some of my garage cabinets are hung with MDF cleats. And those carry a lot of weight.

Re: French Cleat Material

#4

Re: Just about any material

Fred Davis

>Mike ,

I would feel comfortable with the strength of Baltic Birch, I assume you would have a nailer strip on the bottom inside for additional fastening.

I suggests you pay attention to the fastenr more then the material and probably use a washer to prevent the fastner head fron pulling thought the plycore.

FredD

Re: French Cleat Material

#5

Re: French Cleat Material

Jim Dillon

>Robby,

As long as the French cleat is fastened/glued securely to the back of the cabinet and the cabinet back is well fastened/glued, it should work. The width of the french cleat should distribute the weight and, hopefully, the wall cleat will be well fastened into some wall studs. You could even use two cleats and position them carefully. And as Fred suggested, having a bottom cleat might give you peace of mind. I have used a single French cleat on a laundry room utility cabinet that not only is filled with the usual stuff, but 4 cases of canned dog food sit on top and so far it hasn't moved an inch, well maybe 1/2 inch. Just joking 8-). I would give it a try.

Jim

Re: French Cleat Material

#6

use commercial metal ones

Bill Tindall, E.TN

>Lee Valley has them as will as most cabinet supply places.

Re: French Cleat Material

#7

Re: French Cleat Material

mdclor

>I have used 3/4 inch angle iron that I lag bolted into the studs and bolted to the cabinet. It will only move if the house falls down. :)

Merle

Re: French Cleat Material

#8

Re: Rockler has a steel version

Steve in Denver

>http://www.rockler.com/product.cfm?page=347&filter=cleat

Re: French Cleat Material

#9

Re: French Cleat Material

Robby Wright

>Thank you all for your input. Hopefully, the cabinets will be hanging this weekend.

Robby Wright

San Marcos, CA

Re: French Cleat Material

#10

Re: French Cleat Material

Jim Dillon

>Robby,

If I were doing this, I would use one French cleat at the top of the cabinet. Then I would hang the cabinet and slide a ledger board up against the underside bottom of the cabinet and fasten it securely to the wall studs. This way, the weight of the tool cabinet would be supported by the ledger - in addition to the top cleat which also serves to hold the cabinet tight to the wall. Perhaps making the bottom ledger from two pieces of your 1/2-inch Baltic plywood glued together to give a 1-inch thick ledger board would give more peace of mind as well. Let us know how it goes.

Jim

Re: French Cleat Material

#11

Thanks All

Robby Wright

>I used the Baltic Birch with great success. I also added the bottom ledgers that Jim suggested. I used big, heavy screws into the studs, top and bottom. Worked like a charm. I will be posting pictures when I get the project finished. Thanks for all your input and help.

Robby Wright

San Marcos, Ca

Re: French Cleat Material

#12

Re: Thanks All

Jim Dillon

>Robby,

Glad it worked out! Looking forward to some pictures when you get a chance. Thanks for getting back to us.

Jim