Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

Router table design

Posts

Router table design

#1

Router table design

Ralph Lipeles

>I couple of years back I picked up a 16" Incra guide. Finally I am making the time to build a router table for it and I am soliciting ideas. The Incra manual suggests a top that is only 24" by 32". That seems pretty small to me. My Craftsman router table is 34" long and there are times that I wish it were longer. So, any ideas on sizes, design features or any other cleavernesses are greatly appreciated.

Re: Router table design

#2

Re: Router table design

George@Colonel's Workshop-Havertown PA

>Good Afternoon Ralph,

You could make it as large or as small as you want. Shop space is imnportant to many, including myself. My table worked out to be nearly 39 inches long, but that was because I had inhereted a piece of bowling alley for the top. In my view, the cabinet size is as important once a usable table size is established. My cabinet contains a lifting mechanism, a bottom shelf holding hand held routers and bases, and enough drawer apace for all my 1/2" and 1/4" bits. Dust collection port is in the rear. T tracks routed in the top provide for commercial fence positioning. The photo was taken prior to the installation of a lifting mechanism.

George


img

Re: Router table design

#3

Re: Router table design

Ralph Lipeles

>Looks Great! Is lift mechanism commercial or homemade?

Re: Router table design

#4

Re: Router table design

Hal Smith

>I built mine based on the design Bill Hylton presents in his book "Router Magic". Built it about 7 yrs. ago and have no desire for anything else. Stable and solid. Top is hinged for easy access. Good storage space for bits and misc. Fence is simple, but functional. By offsetting the router mounting from center by a considerable amount, you can work from the back if you have a large workpiece. I added a small box on the back of the fence for connecting, a shop vac, but don't use it much since the dust collection method built into the design is satisfactory. Good luck. Hal

Re: Router table design

#5

Lift Mechanism

George@Colonel's Workshop-Havertown PA

>Good Afternoon Ralph,

After a lot of thought I decided to install a commercial mechanism rather than fabricate my own. You'll $pend a lot on a commercial mechanism; worth it to me because I frankly don't believe I have the requisit skill to have built my own--and I didn't want to waste time screwing around when I know a commercial one would work right away. I bought a JessEm Mast-R-Lift for my P+C 7518. Heretofore, I used a P+C 690 for nearly all my work. Used the big boy for raised panels and other wide bit applications. It was time to retrofit a commercial lift when I couldn't see well enough to achieve a desired bit setting. The JessEm works as advertised, but I am no fan of it or the company. I do like the comercial fense I use. Its a Penn State Industries product. Well made and relatively inexpensive.

George

Re: Router table design

#6

Re: Lift Mechanism

Fred Davis

>George,

remember the lift mechanism the guy in the table saw clip developed??

Now there's a idea ;-))

FredD

Re: Router table design

#7

Fred, That guy could get "board" to death

George@Colonel's Workshop-Havertown PA

>

Re: Router table design

#8

Re: Router table design

Dick Coers

>I made my top, 22x36. I have an Incra Ultra, and I think that is 24". I offset the router from side to side so I could use the length of the Incra without it hanging way over the table. I put the router 24" from the right and centered front to back on the 22" dimension. So far, I don't mind working on the 22" width. If the part is much more than 48" long, I take the router to it. I use the Dewalt 625 (3 hp) with a router razer. I'm not sure those are made anymore, but it sure works great. Sorry, pics would be too embarrassing. Man I have to clean the shop.

Re: Router table design

#9

Re: Fred, That guy could get "board" to death

Fred Davis

>GEORGE!!!!

I can't stand it LOL

FredD

Re: Router table design

#10

I especially liked

Bill Houghton, Sebastopol, CA

>that, instead of hooking the bail over the board, he balanced the pail on the board. Maybe we should consider requiring a license before someone can buy a power tool.

Re: Router table design

#11

Re: Router table design

del schisler

>this is the one i use I didn't want to build one I wanted to get going I did build the botton and side's The top came already made this site has lot's of items

http://us.oak-park.com/catalogue.html?list=BYOT--

Re: Router table design

#12

Re: Router table design

Steve in Denver

>Norm's router table has some nice features, http://www.newyankee.com/getproduct.php?0301

I would also look at the Incra and Woodpeckers web site for ideas. Woodpeckers lifts are all high quality, I couldn't imagaine making a lift, at least one you'd be happy with.

Re: Router table design

#13

Re: Router table design

Dave Paine

>I have an Incra 16 in router fence. Purchased from Woodpeckers. I also purchased a 27 in x 32 in table top also from Woodpeckers.

My table top has the mitre channel left to right on the 27 in width.

I have never used the depth of my table. The most depth I have used was perhaps 6 in. Typically 1 - 4 in.

I have frequently wished my table width was 32 in vs 27 in.

If I were starting again, and building my own table, I would make it at least 36in wide and perhaps 24in deep.