Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

Slightly OT: drilling holes in masonry

Posts

Slightly OT: drilling holes in masonry

#1

Slightly OT: drilling holes in masonry

wilbur

>I've been drilling holes in the walls of my basement and using wedge anchors to attach 2x4s to the walls, so I can start getting some storage in my shop. After drilling about 20 holes, it seems that the bit gives out after 6 holes or so.

I've been using a regular drill, not a hammer drill, to drill these holes. The actual drilling seems to work pretty well, until the bit stops working. Examining the cutting edge shows that the carbide edge is rounded over. I've read that using a hammer drill makes this job easier, but will it lengthen the life of the bit?

Re: Slightly OT: drilling holes in masonry

#2

Re: Slightly OT: drilling holes in masonry

Bill Howatt

>Probably is my best answer. Drilling with a regular drill usually goes fairly well until it hits a "large" stone in the concrete; large being one that is big relative to the hole diameter. The drill does a lot of spinning on the hard stone before it manages to get through it and this is hard on the bit. A trick you can use is to drill until the penetration slows and then put a small pointed punch in the hole and and hit it with a good hammer a few times which should break the stone. Drilling should then go easier until the next one.

I finally broke down and bought a cheap hammer drill because I only needed it for one more project. I said that about 6 projects ago and my neighbour has borrowed it too. Worth a thousand times more than I paid for it; you can't believe the difference it makes!!!

Bill

Re: Slightly OT: drilling holes in masonry

#3

Re: Slightly OT: drilling holes in masonry

Ralph Lipeles

>A hammer drill will do much better for you. These carbide drills are made very cheaply and as you have seen, fail quickly. The action of the hammer drill beats, pounds and pulverizes the cement that you are trying to remove. It will do the same to any gravel that may be in the drill's way. I don't think that it makes much difference on how sharp the bit is.I borrowed one for attaching a 2 x 12 deck header to a poured concrete foundation. The holes were 3/4". The drill went almost as quickly as if it were going through wood. You might want to start with 1/4" holes then open them to 1/2" holes. The smaller holes will make it easier to keep the bit from wandering.

Re: Slightly OT: drilling holes in masonry

#4

Slow speed

Al Goldstein

>I too recommend a hammer drill. But even with a hammer drill it is important to not spin the drill bit too fast. For many years I was burning up my carbide bits drilling into concrete walls. Then I discovered that I was running my drill at high speed and overheating the bit. The rounding of the edges of your bits is a clue that the same thing is happening.

I've found that the key is to watch the debris coming out of the hole and back off on the drill speed when the debris starts to come out slowly. The best drill speed is when the debris comes out fastest.

Good luck.

Al

Re: Slightly OT: drilling holes in masonry

#5

Re: Slightly OT: drilling holes in masonry

John Luke

>One word,

Ramset

Re: Slightly OT: drilling holes in masonry

#6

Re: Slightly OT: drilling holes in masonry

Gary Evans Tallassee, TN

>I agree with the consensus on using a hammerdrill for your task. I would also add that it's worth the extra to buy the hammerdrill bits from Bosch. They'll last lots, lots longer than a standard carbide bit.

Gary

Re: Slightly OT: drilling holes in masonry

#7

JL

Ramset (or something similar)

JL

>works well for me. I had to put "firring strips" on the walls in my basement and I had to nail the bottom plates of my walls to the concrete floor. I gave up and bought one. It was nice to just pull the trigger and shoot a nail in.

Re: Slightly OT: drilling holes in masonry

#8

Re: Pouring the water also helps

Alexander Grigoriev

>

Re: Slightly OT: drilling holes in masonry

#9

Bingo!

Rod Peterson -- Ormond Beach

>> You might want to start with ¼" holes then open them to ½" holes.

This is the technique I've used successfully for years. Same for drilling holes in metal. Depending on the size of the ultimate hole, I may use three or four bits before finalizing the desired size. It's a whole lot faster than trying to jump to ¾" right off the bat.

Rod

I wonder how it's done in California.

Re: Slightly OT: drilling holes in masonry

#10

Hammer drill-YES!

Bill Tindall, E.TN

>I bought one of these at last and believe me they drill holes in concrete vastly faster. I wish I knew to own one years earlier. Because they drill faster the bits don't wear as much per hole. Masonary bits are easy to sharpen.

Re: Slightly OT: drilling holes in masonry

#11

Hammer drill vs. rotary hammer

Bill Houghton, Sebastopol, CA

>If your project is such that you can identify all the holes you'll need and drill them in one drilling orgy, you can rent a tool from your local rental yard and get the job done in one afternoon or less.

There are two tools: hammer drills and rotary hammers. Rotary hammers, which let the bit slide back and forth a little, are faster and easier on your body because they absorb much of the shock. Hammer drills are cheaper. I've read that hammer drills are fine for up to 1/2", but, after scoring a rotary hammer at a charity rummage sale (almost unused Bosch for half discount-store retail), I would never bother with a hammer drill.

Still, some rental yards offer only the serious rotary hammers, optimized for holes of 1" and up, which is kind of overkill for a few 1/2" holes. If the hammer drill is way cheaper, that should be OK too.

I probably am telling you what you do anyway, but wear a dust mask and safety glasses. Concrete dust is nasty stuff in a closed space.

Re: Slightly OT: drilling holes in masonry

#12

Re: Ramset (or something similar)

Fred Davis

>another aspect of the powder actuated device (Ramset for instance) is ,if you have the the right gun, they will shoot threaded studs into concrete, which eliminates a step from drilling holes..

FredD