Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Dust Collection Fitting?

Posts

Dust Collection Fitting?

#1

Dust Collection Fitting?

Mark Mandell - Gone Round In Jersey

>I've gone through every DC merchant site I could find (PennSt, Oneida, general ww vendors) without success.

What I'm looking for is a fitting that will work as a quick connect (even not-so-quick) to join 4" DC flex hose to 4" S&W PVC fittings. I've been making my own by sectioning and regluing pipe, but the constructs are not as durable as I'd like.

Seems like SOMEbody aught to be making these things.

TIA

Re: Dust Collection Fitting?

#2

Re: Dust Collection Fitting?

Alan in Little Washington (NC)

>I stick my flex inside the bell end of S&D. It is a tight fit but eventurally goes in. I cut the bell end off, leaving about 2 -3" of pipe which becomes the male end of a quick fittings that will fit in another bell end or a connector (all my blast gates are made with one side 1/2 of a fitting and one side a section of pipe.




Re: Dust Collection Fitting?

#3

Try RV suppliers...

Jim Rahbe

>Mark,

Check out RV supply houses. Not sure they have the exact fittings you are looking for, but they do carry a number of different quick disconnect fitting for flex pipe.

Jim R.

Re: Dust Collection Fitting?

#4

Fittings

Mark Mandell - Gone Round In Jersey

>Why do I think there must be a lot of S&W pipe lying around without bells?

Never though of trying that. Seems a good fix.

Re: Dust Collection Fitting?

#5

Re: OT Shop Floor

GalenV

>Alan

From the picture of your shop floor it looks like if I dropped my chewing gum I could pick it off the floor and start chewing it again!

How often do you have someone come in and polish the floor!

Do you have to wear special tinted safety glasses to cut down the reflective glare?

Fantastic shop setup!

Galen

Re: Dust Collection Fitting?

#6

Re: Fittings

Alan in Little Washington (NC)

>I am using mostly 6" S&D, but this is even easier with 4". Turn a round wooden wedge- one end smaller than the S&D ID, but taper it so the other end is larger- the same diam. As the OD of the flex. Use a propane torch to soften the PVC than use a small sledge to drive in the wedge to make your own bell ends. Works great, and easy to do.

Re: Dust Collection Fitting?

#7

Thanks, Jim

Mark Mandell - Gone Round In Jersey

>I'm not in a "big" RV area but I know of several west of me in PA. Maybe I'll drop in the next time I'm out that way.

Re: Dust Collection Fitting?

#8

Woodcraft # 145986 = 4" hose to PVC &

Art Silva

>145985 = gates to 4" PVC.

Re: Dust Collection Fitting?

#10

Close But

Mark Mandell - Gone Round In Jersey

>Not quite there. That fitting connects 4" hose to 4" PVC pipe. The tech informed that it wouldn't seal in a PVC bell. May work, however, if I glue a piece of 4" pipe around the fitting.

Progress. Thanks

Re: Dust Collection Fitting?

#11

Called

Mark Mandell - Gone Round In Jersey

>A very nice woman pulled out their fittings and measured them for me. They're made to fit into 4" flex and then over a standard machine port. The flair end (being a smidge under 4" ID) won't fit inside the Sch. 20 bell.

Thanks for the link.

Re: Dust Collection Fitting?

#12

Schedule 40 to SD

A Wright

>I have used a female SD to a male Schedule 40. The schedule 40 PVC fitting is small enough that the 4" hose will slip over it, and the other end will go over any SD pipe

I think I bough this one at Lowes


img