Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Band Saw Blade Sharpening

Posts

Band Saw Blade Sharpening

#1

Band Saw Blade Sharpening

Dwain

>I have a 14 inch Delta band saw and I've been trying to find a sharpening service on line that I could send my dull blades to, to have them sharpened?

I've had no success, so I'm drawing two conclusions: One that it is something you do yourself and Two the cost to sharpen them is not worth it both to myself to send them off and to the person I would send them to.

If I'm wrong can someone recomend a service.

Thank you,

Dwain

Re: Band Saw Blade Sharpening

#2

Re: Band Saw Blade Sharpening *LINK*

Stuart Johnson

>Here is a link on sharpening our own. I do mine and it works great.


Band Saw Blade Sharpening,

Re: Band Saw Blade Sharpening

#3

Re: Band Saw Blade Sharpening

Jim Pugh, Elyria, OH

>Dwain, it would be helpful to know how coarse your bandsaw blade is. You can sharpen 3 or 4 tpi youself.

Re: Band Saw Blade Sharpening

#4

Re: Band Saw Blade Sharpening

John K Jordan

>Dwain,

I've never heard of a commercial service for this.

You may want to search the archives on the Turning board for much info on sharpening them yourself. I resharpen all of my coarser blades at least twice. I use a method similar to that in the link Stuart provided but I DON'T swing the Dremel disk downwards across the tooth - I think that is likely to round over the tip. I simply hold the Dremel at the right angle and briefly touch the disk to the tooth. This grinds a tiny flat on the very tip of the tooth and works great. I can't tell any difference whether I align the disk with the tooth (left, right, center) or simply grind them all straight on.

Some have said this is too time consuming or tedious and they prefer to buy new blades. I timed sharpening a 142" blade and it took me 8 minutes. A new blade would have been at least $30. $200+ per hour is not a bad return. It gets even better as the blade price increases.

I'll sharpen 4tpi blades but I don't think I'd attempt one much finer.

JKJ

Re: Band Saw Blade Sharpening

#5

Re: Band Saw Blade Sharpening

william h. falberg

>The guy in the video is doing it the hard way and probably creating blade drift by leaving a burr on the side of each tooth. Take a Dremel with a small cylindrical-shaped diamond abrasive and just stroke downward, tool perpendiculsr, rotation in-line with the blade, on the back of each tooth, full speed. Use a cup of water to dip the diamond in, and keep it cool or you'll lose it.

Re: Band Saw Blade Sharpening

#6

Re: Band Saw Blade Sharpening

Barry Irby

>You said: "$200+ per hour is not a bad return." I point out that I sharpen them on the saw. Takes me longer to change and realign the blade than to sharpen it. Well, it takes me more than eight minutes, but it still takes about as long to change one as to sharpen it.

I found they work nearly as well as a new blade, but not quite. Not good enough for serious resawing, but great for most anything else.

Re: Band Saw Blade Sharpening

#7

Re: Band Saw Blade Sharpening

John K Jordan

>>Not good enough for serious resawing, but great for most anything else.

ESPECIALLY when you've just ruined the edge on a new blade! This happened to me a few weeks ago. Someone gave me a 3" thick slab of what turned out to be walnut probably 100 years old. I cut of 24" and made several rip cuts with a brand new Starrett bimetal blade, close to $50 if I remember. The blade was so dull it would barely cut anything. You can bet your sweet bippie I sharpened that blade rather than toss it. I've used it for 100's of cuts since then and it still cuts like a hot knife through butter.

It was Brian Haun on the Turning forum who's comments and instructions first encouraged me to try sharpening. (in archives) Steven Russell also has an article on sharpening, although I like Brian's method better. BTW, I've found no effective difference between sharpening on the top side of the tooth or the inside other than after several sharpenings you start to lose a bit of the set in the teeth. The top-side method is FAR quicker and I think easier to get right. A rotary bit in the gullet requires more manual control to prevent rounding over the point.

JKJ

Re: Band Saw Blade Sharpening

#8

Re: Band Saw Blade Sharpening

Curly Smith

>Your local Woodcraft, Rockler, or similar store can give you the name of a sharpening service in your area. Call them or send them an email. Or, you can consult your phone book under "sharpening service". It won't be cost effective to mail a cheap blade back and forth.

If you use the cheap blades, as I generally do, then you're better off learning to sharpen them yourself as describe in posts above. You can use a local service for the other more expensive blades.

Re: Band Saw Blade Sharpening

#9

Re: Band Saw Blade Sharpening

Dwa

>Well, doing it myself was the conclusion I started to come to and I really appreciate all your input.

Thank you,

Dwain

Re: Band Saw Blade Sharpening

#10

Re: Bet Your Sweet Bippie?

Dave Anderson (PacNW)

>OOOO! You let the cat out of the bag! You are really old, just like me.

Re: Band Saw Blade Sharpening

#11

(Hijack) for John Jordan and others.

Barry Irby

>John, A couple of questions. Based on the article several years ago in FWW, I bought ten or twelve identical 1/2" 3TPI blades for my 14" Delta saw with a riser. My theory was that these would be my go to blades for most everything. Resawing, bowl blanks, whatever. I have a Love/HATE relationship with the bandsaw anyway. Changing blades Drives me nuts. I want that illusive universal all purpose indestructible blade. Now for the questions. Don't you have a WoodMizer or similar mill? How long do those blades last? (And exactly how high is UP?) I assume you get hundreds of feet of ripping lags into planks. On my saw I would be thrilled to resaw a hundred feet, with twenty being more likely.

I would buy a carbide tipped blade, but they seem to cost about ten times as much and I ruin blades by getting a bend or kink in them. The one on the saw now has such a kink and I really don't know where it came from. Sometimes I know what happened such as it grabs the blank while sawing a bowl blank, but this time????

So, I find it takes about thirty minutes to change from one type of blade to a different type if I have to adjust all the guides and rollers. If I change to an identical blades it take about fifteen minutes. Much less fiddling.

As you mentioned, dulling a fifty dollar blade is a bummer, but a ten dollar one...not so much. A hundred dollar one would ruin my day.

Just trying to figure out why my blades don't last as long as the Woodmizer ones.

Re: Band Saw Blade Sharpening

#12

Re: (Hijack) for John Jordan and others.

John K Jordan

>Barry,

I haven't thought about comparing the Woodmizer to the upright bandsaw, but I do seem to get a lot of use out of the sawmill blades. I bought 20 blades with the sawmill and am on my 10th blade after about three years. A couple broke, one jammed (my fault) some were dulled by black locust, one by metal in the wood, and one when I ran into the dogs. (they say everyone does this once!) Blade life also decreases if you are dragging grit through the kerf from dirt on the bark and is worse for some species. I haven't kept track, but I do seem to get many 100's of board feet from each blade under normal circumstances.

However, - the wood is green, the blades coarse (1 tpi or so?), they seem to run at a faster linear speed (haven't checked though), are driven by a 15 horse engine, and the cut is constantly lubricated by liquid from a tank. Perhaps some of these things make a difference. I suspect in resawing hard, dry boards with more limited power you might more easily notice when the blade starts to dull where the sawmill may continue plowing through with brute force. Don't know for sure, but I do know that when I change a blade that is too dull to cut well it feels REALLY dull to my fingers. I haven't tried to resharpen any. Woodmizer has a Resharp program that costs about $7 per blade and they do the first 10 for free. Almost time for me to send some off.

BTW, I'm about to saw a bunch for my new barn constructions. Before I was sidelined a few months ago I cut a huge pile of logs into cants to make them easy to throw up on the mill for boards sized as needed.

JKJ

Re: Band Saw Blade Sharpening

#13

Re: (Hijack) for John Jordan and others.

Curly Smith

>You didn't say what you're resawing but a few things come to mind:

a) Speed kills bandsaw blades -> too high a feed rate causes the blade to get hot and a hot blade is a dull blade. Take your time and let the blade clear the sawdust. Watch the back guide - if it's spinning like crazy then you're going too fast. If you've equipped your saw with a dust connection in the lower section and you have a lot of sawdust buildup on the table then you're pushing too fast. Note that "spinning like crazy" and "a lot of sawdust" are relative terms.

b) Bark kills bandsaw blades -> if at all possible remove the bark. The dirt in the bark will rapidly dull your blades.

c) Proper tension should be applied -> if you don't have enough tension the blade will deflect too easily and you'll get a bowed cut. The bow will cause friction which will heat the blade which will cause the blade to get dull.

d) Friction is not your friend. Wax your table, your sleds and your fence to reduce the friction as much as possible. The more you have to push to overcome friction the more likely you're going to push too hard and either deflect the blade or cut too fast.

d) Use the right blade -> the 1/2" 3 TPI may not be the best choice. If you're cutting stuff thicker than 6" consider moving to a 2 TPI blade, if less than 1" consider a 3/4 variable or 4 TPI (or greater if much thinner).

e) Kinks happen when the work isn't properly supported. If you're resawing tall stuff then your stock fence isn't tall enough. Either add an auxiliary fence or make a new one. Ideally, you'd like to have support for the entire height but rout grooves to remove 2/3rds of the material - you want support but you don't want full contact along the height because of the friction. If you're cutting flats on log sections consider using bungee cords to straps to hold the wood. If the piece moves while cutting you'll get a kinked blade.

f) Consider making a very simple resaw sled. You'll need a piece of 3/4" plywood, two aluminum t-track hold downs (as shown here: Large Aluminum Hold Down ), a 3/4" runner for the slot, a couple of bolts and knobs, and a Bessey clamp. The plywood should be a few inches longer than the maximum capacity of your Bessey clamp, the width should be slightly more than the width from the blade to the outside edge of your table. Cut a groove for the runner in the plywood base about 1/8"less than the distance of the blade to the slot (you'll cut off the excess later), make sure that the runner is snug but slides freely. Wax the table, the bottom of the sled, the slot, and the runner. Tap the runner into the bandsaw table slot and then cut off the extra width from above - you now have a cut-off sled for the bandsaw. The blade will ride the inside edge until you change blades (and/or the drift changes). Place the Bessey Clamp 1/8"-1/4" from the cutting edge, and mark bolt hole locations for the two hold downs. Drill and countersink holes for the bolts, and then install the hold downs to firmly clamp the Bessey to the sled then simply tighten the Bessey clamp to hold the wood (note: a 1/4" piece of plywood under the jaw will help it slide without requiring loosening of the hold down). The Bessey clamp will hold the work securely and the hold downs will hold the Bessey clamp securely to the sled. Since the table and the bottom of the sled are waxed finger tip pressure is all that is needed to push the piece through the cut. Just remember to account for the kerf when making the cut.