Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

DeWalt 734 planer won't feed: cold rollers?

Posts

DeWalt 734 planer won't feed: cold rollers?

#1

DeWalt 734 planer won't feed: cold rollers?

Dan Mitchell

>Went out to my unheated shop to do a bit of planing, 1st time out there in 6 weeks or so, due to the "unheated" aspect. I'd say it's between 40 & 45 out there right now. Went to plane a piece of hard maple, about 3/4" x 10" x 18". Even with a minimal cut, the board won't feed. Tried some smaller pine pieces, one also ~3/4" thick but only about 2" wide, same story. Won't even start feeding, & if I give it a shove, it stops moving as soon as I stop shoving. "Shoved" portion is planed fine, but no feed. Machine is about 1 year old, has seen minimal use. Is this a result of the rollers being cold? Anything I can do about it, other than bringing the planer inside for a few hours (which would be a PITA due to the way it's mounted)? It was fine the last time I used it, again, maybe 6 weeks ago.

I was REALLY hoping to make some sawdust! ;-(

TIA

Dan

Re: DeWalt 734 planer won't feed: cold rollers?

#2

JL

Have you cleaned the rollers?

JL

>Recently? Ever?

If not, they may be dirty. I usually clean them with isopropyl or ethyl alcohol and a rag. Wear a glove, both will dry your hands out really quick.

Re: DeWalt 734 planer won't feed: cold rollers?

#3

Try waxing the bed

Jim in VA

>It's amazing what a difference waxing the bed can make. I had the exact same problem you had on my 16 inch jointer/planer combo. Some wise person told me to wax the bed. I was skeptical that such a minor thing could make a difference, but I tried it. Problem solved.

Re: DeWalt 734 planer won't feed: cold rollers?

#4

Re: DeWalt 734 planer won't feed: cold rollers?

Jerry Gibbs

>Last time I had a feed problem, the cutters were dull. You have a lot of variables. Maybe temporary heat such as from a salamander will give you an answer. Jerry Gibbs

Re: DeWalt 734 planer won't feed: cold rollers?

#5

Re: DeWalt 734 planer won't feed: cold rollers?

Dan Mitchell

>Thanks for the replies. I have wiped down the rollers with alcohol, but not for awhile. I did think of waxing the bed, but I was a bit concerned about having wax residue on the wood come finishing time, even with some sanding before hand. Not an issue?

Dan

Re: DeWalt 734 planer won't feed: cold rollers?

#6

Re: DeWalt 734 planer won't feed: cold rollers?

Barry Irby

>The replies have hit the three or four things I could think of: Clean the rollers, wax the bed (Careful, not the rollers), sharpen the knives or change them, and apply some local heat. I have a small electric "Barn" heater and it does wonders for my shop.

One other thought, have you looked to see if the rollers are turning? Probably are, but it wouldn't hurt to take a look. Of course, if they are not, you have a whole different problem.

Re: DeWalt 734 planer won't feed: cold rollers?

#7

PS......Make sure your wax does not include

Barry Irby

>silicon. Or is it silicone?

However it is spelled silicon will be a disaster in some finishes. It is not usually included in good paste wax but might be in some of the "easy" spray cleaner/waxes.

Good quality paste waxes don't seem to bother most finishes.

Re: DeWalt 734 planer won't feed: cold rollers?

#8

Re: Try waxing the bed

slozuke

>I'll second waxing the bed. I have the same planer and "had" the same problem. I found just cleaning and waxing the bed made a world of difference. It never hurts to clean the rollers once in a while either.

Hope that works.

Re: DeWalt 734 planer won't feed: cold rollers?

#9

Re: PS......Make sure your wax does not include

Pete in Holland, MI

>Silicon = material used for electrical chips

Silicone = used as a lubricant and sealer

If your planer has urethane or rubber faced rollers, in a cold envrioment, they will be harder and less supple, thus may be the reason they are not grabbing & pulling your wood.

Re: DeWalt 734 planer won't feed: cold rollers?

#10

Re: DeWalt 734 planer won't feed: cold rollers?

Dan Mitchell

>Thanks for the replies. I have a can of Johnson's paste wax which I've used on my table saw, I don't think it contains silicone, I'll try that.

I did check to make sure the rollers are rotating.

Re: DeWalt 734 planer won't feed: cold rollers?

#11

The wax did the trick! ;-) :-) ;-) ;-) ;-)

Dan Mitchell

>