Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Delta Unisaw Fence

Posts

Delta Unisaw Fence

#1

Delta Unisaw Fence

Don Evans

>Just FYI -- I discovered a site that has a replacement guide for the Unisaw fence. For those who have this fence instead of the Bessy type you can have both worlds.

I'm just a happy customer but:

http://www.ptreeusa.com/uni_t_fence.htm

in Atlanta sells a replacement for the aluminum extrusion on the unifence that has "T" slots, 1 on side towards blade, 2 on top and another on right side. The great part is that you just loosen the two knobs holding the original, slide it off and this one just slide on. The tape measuring guide doesn't even have to be readjusted.

NOTE: they have other fences on the site, so make sure you find the one just for the uni.

It opens the door for jig attachments like the Bessy and with the added T slots even more jig designs.

They have other good stuff like the "stay put" dust collection hose, check it out.

I'm not happy with the clamp assy for the delta miter but that same design works great on the drill press table. So I would stay away from the clamp for the miter guage. I'll probably send mine back.

Don

Re: Delta Unisaw Fence

#2

Re: Delta Unisaw Fence

A Wright

>I've had one of those replacement fences from Peachtree for a few years and I am very happy with it. I took my original fence and shortened it with a hacksaw to use with my miter guage for cut-offs

Re: Delta Unisaw Fence

#3

Re: Delta Unisaw Fence

Chuck in ND

>I've seen the fence face replacement before, and it looks like an ok deal if you want a sacrificial board on the fence. As far as useing Board Buddies and or feather boards with a Unifence I think is a bad idea. The fence does not lock down in the back, so when useing those accesories the fence wants to lift, which I would think puts a unneccesary strain on the fence main casting and rail.

Re: Delta Unisaw Fence

#4

Re: I think you're missing the point

Dave Mount

>I don't think the appeal of this fence is having a sacrificial face, in fact I don't think the UHMW is supposed to be sacrificial, just a slick and hard wearing face.

The main advantage I see is having a parallel face on the far side of the fence, as well as the T slots on top, to make attaching fence fixtures much easier. I had a Unifence for many years and, while I liked it overall, it was sometimes difficult to clamp featherboards etc. to the fence because the right side of the extrusion was not parallel to the left.

With regard to uplift issues, I don't believe any of the precision fences clamp at the back, it's part of how they ensure that they lock parallel consistently. I don't see why this would be any greater an issue for a Unifence than for others. My current Bies clone doesn't lock down in back either. I routinely used shopmade featherboards on the Unifence; they result in upward pressure on the fence and it was never an issue.

If I still had a Unifence, I might consider this as an alternative fence for general use. The one thing these don't offer that a Unifence does is the low profile position for ripping. I always liked the low profile and the ability to keep your hand half on the workpiece and half on the fence, enabled by having the Unifence in the "down" position.

Dave

Re: Delta Unisaw Fence

#5

Re: I'm missing the selling point ?

Chuck in ND

>I stand by all of what I said. Weather it's meant to be sacraficial or not, the strip is alot cheaper to replace then what it's attached too, or a new Unifence fence. I wouldn't do the feather board or the Board Buddy either, the cam in the main fence casting is easier to break than you think.

Re: Delta Unisaw Fence

#6

Re: I'm missing the selling point ?

A Wright

>I have had the fence for 3+ years, and never replaced the UHMW strip. I guess if I wanted to I could by a second strip or make one out of 1/2" MDF, but that seems like too much trouble. If I need a sacrifical fence, I clamp a piece of wood to the face of the fence.

As for Board Buddies, I use them with my Uni-fence pretty often and have never had any problems.

Re: Delta Unisaw Fence

#7

Re: I'm missing the selling point ?

Don Evans

>Regarding the sacrificial part of this unit...

The UHMC is NOT meant to be sacraficial, you remove it and plane a board down to 1/2" and install it where the UHMC is if you want to do work that needs a sacrafice.

Best point for me is the tape measure on the saw stays accurate when using this fence.

I also like the shape so jigs fit it like the Bies type shop made jigs.

I also cut off 10" of the old extrusion and use it with the miter and can still switch back to the other extrusion if I need the low profile for the saw guard.

Just thought some would be interested in it, some will not see any advantage and thats ok.

Don

Re: Delta Unisaw Fence

#8

Re: I see one selling point

Chuck in ND

>I didn't say that I didn't see an advantage to it, I just don't see all that were posted. I have a Unifence on a Rockwell 9" Contractor's table saw, and a previous owner of the saw aparently got a little too close to the fence with the blade. So in a situation like that, I'd much rather have to replace the insert on this fence than have to replace the whole fence, it would certainly be alot cheaper.