Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

making cove on tablesaw

Posts

making cove on tablesaw

#1

making cove on tablesaw

Don Evans

>I'm familiar with the method of setting up two guide boards with enough space between them to run a board through and raise the blade for the depth for cutting a semi circle out of a board for cove moulding.

My question is sizing it: the depth is easy, just raise the blade that amount. However, is there a way to calculate the width of the cove based of the angle the board will travel across the blade?

Also the diameter of the blade would also come into the calculation, it seems.

Obviously I have not giving this much thought yet, but I admit my ignorance with this particular procedure, can anyone help me get started here.

An example would be, I want to run a cove that would be 1/4" deep and 1.5" wide in the surface of a board.

Don

Re: making cove on tablesaw

#2

Re: making cove on tablesaw

A Wright

>The simplest way to calculate it is to raise the blade to 1/4" and measure the width of the blade that is over the table.

To calculate the angle between the guide and the blade use the following formula:

arccosine ["width of cove" / "width of blade"] + 90 degrees.

Re: making cove on tablesaw

#3

Try This

Ken Krawford

>Don,

I think this calculator at Fine Woodworking may work for you.

Click right underneath the author's name for the calculator.

Re: making cove on tablesaw

#5

Funny you should ask... *LINK*

Tony - Memphis

>I wrote some software to do just that...hope it helps....I tried to make it very easy to use. If you email me, please be patient, I forget to check this email and the one on my web site.

Tony

You can download it here...

http://www.paintandsawdust.com/tony-covecutter.htm


Cove Cutting Software

Re: making cove on tablesaw

#6

Re: making cove on tablesaw *LINK*

Fred Davis

>Don,

don''t let a easy job be more difficult then it is.

Take a look at the link of my workbench and shop shot 876.

If this is what you had in mind , I will send you a couple of pictures showing the setup on a small Delta tablesaw I use just for this operation.

FredD


http://picasaweb.google.com/FredD17209/20080801?authkey=zVXOj34HN48&feat=directlink

Re: making cove on tablesaw

#7

Frank Klausz III Pamphlet

Ellis Walentine, Host

>Frank Klausz's son published this 13-page pamphlet in 1993, detailing the tilt and approach angles for many odd-shaped and conventional coves. It also has some good background information, explanatory text, and safety pointers. I just checked with Frank, and he still has some for sale for $10 each plus $2 S&H. If you're interested you can call Frank's Cabinet Shop and order one. The number is 908-658-4396.

Ellis Walentine, Host


img

Re: making cove on tablesaw

#8

A cove-cutting secret

Ellis Walentine, Host

>All the programs and pamphlets you see generally assume a 10" diameter blade. I always found that regular saw blades leave a scratch pattern in the cove that needs to be scraped or sanded smooth afterwards. I used to use a round-nose cutter set in my old Delta molding cutterhead instead. It was a small diameter (~6"?), but the roundnose cutter practically planes the wood smooth as it cuts. CMT and others may have fixed-knife cutterheads like this. If you're going to do a lot of coving in the future, it might be worth the investment.

Cheers,

Ellis

Re: making cove on tablesaw

#9

Re: A cove-cutting secret

Fred Davis

>Ellis ,

I thought I was the only one that did that , talk about a old woodworker ;-))

FredD

Re: making cove on tablesaw

#10

Eliminate scratches

Lee Schierer - McKean, PA

>You get a much smoother cut if you use a blade with raker style teeth. If you feed the wood slowly you will see almost no scratch marks.

Lee

Re: making cove on tablesaw

#11

Re: Eliminate scratches

Jay St. Peter - Southern, MD

>I used a wobble dado blade I had around. Much smoother than some other combo blades I've tried, but probably not up to the standards of Ellis'. There was still a little work to be done. Main reason I used it was because of the 7" diameter, who knew it would wind up being a better blade anyway.

Jay

Re: making cove on tablesaw

#12

Blade diam is input...

Tony - Memphis

>I assumed some folks would use something other than a 10" blade, so the user can adjust the blade diam. in my program. It is not fixed.

Tony

Re: making cove on tablesaw

#13

Re: Blade diam is input...

Don Evans

>Thanks everyone I'll check all the links out.

Ellis, appreciate the tip, I have had a 6" molding unit for tablesaw since the 80's. It is a Sears (uck) unit with 4 different type blades but one set is rounded.

I'll give it a test run.

Don