Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

OT Furnace Blower Advice Needed

Posts

OT Furnace Blower Advice Needed

#1

OT Furnace Blower Advice Needed

Sawman

>Here is the situation. I installed a solid fuel furnace and it came with a direct drive furnace blower. I do not like the noise of the motor that is transmitted through the ductwork. Even though it is on isolators for sound.

So here is my idea. I get a belt drive blower,extend the shaft and mount the motor "outside" the ductwork. I would put a guard around the belt for safety.

So what do you think?

Also what kind of motor would I need in order to control the speed?

Thanks!

Re: OT Furnace Blower Advice Needed

#2

Re: OT Furnace Blower Advice Needed

GalenV

>Before you could make a switch of any kind you need to know the capacity of the current blower. I would think the literature to unit may give the CFM of air and hopefully the static pressure of the rated air. Belt driven blowers I used were Peerless-Winsmith, Berry and even some from Grainger.

If heater is new I would find out if the noise you are hearing is "normal" to their unit. Could be you have a problem or not installed properly.

If the motor is just mounted on rubber groment for isolation maybe it is the entire blower vibration in the way it is ducted. There are rubber boots that can isolate ductwork.

Since I really don't know how this blower mounts in unit hard to say if your conversion is practical.

You find all kind of things: I had a Lennex pulse furnace and it made a rumble sound. Found the set screw holding the fan to motor shaft was loose and until by friction it came up to speed the shaft spun in the fan bore creating the sound. Hey, you might check that.

Galen

Re: OT Furnace Blower Advice Needed

#3

Re: OT Furnace Blower Advice Needed *LINK*

GalenV

>I need to correct that blowers use were Peerless Blower as Peerless- Winsmith was our gear boxes.

What size is this blower by wheel size. Most suppliers make interchangable blowers by dimensions so maybe you need a better quality blower.

I assume you checked the blower wheel is not rubbing the intake sheet metal. Usually these blower run quiet unless they are improperly mounted.

If you have a parts manual post it so others can see what and where this blower is since not in a conventional gas furnace.

Did you post before this was going to be in parrallel to your conventions furnace?

Galen


Peerless Blower

Re: OT Furnace Blower Advice Needed

#4

Re: OT Furnace Blower Advice Needed

Sawman

>Galen,

Thanks for you reply.The furnace manual is vague so it does not show the blower mounting. This is installed with my gas furance being seperated with a back draft damper. I may have posted something in the past.

I was fussing with a few wood shims and found a few vibration points. So I will continue to tweek it.

Though I still think the idea of a belt drive is the way to go.

Tom

Re: OT Furnace Blower Advice Needed

#5

Re: OT Furnace Blower Advice Needed

Barry Irby

>Not at all sure, but I thought the direct drive blowers were quieter than the belt drive units.

Is your duct work isolated from the furnace by the vinyl collars? It should be.

The other thing I was taught is that most of the Moise travels down the ducts because they are metal. Either use flex duct or line your metal ducts with insulation. What I was taught was that lining the first fifteen feet of the ducts would dramatically reduce the noise. This is "Old School" as my kids say.

The ducts made of fiberglass duct board are quieter, but controversial because it is possible the fiberglass sloughs off inside the duct and blows out into the the air.