Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Getting organized

Posts

Getting organized

#1

Getting organized

Ellis Walentine, Host

>Hi folks,

Since one of my New Years' resolutions is to organize my office, I decided to start by doing something about all the shoes that I've been tripping over for the past ten years. So, I made this quickie shoe organizer for the back of my closet door. Sure, it won't win any design or craftsmanship awards, but it works great. I made it as quickly as possible; even that wasn't quick enough for me.

Now I have more floor space to pile magazines and books in. :-)

Cheers,

Ellis



This dwg isn't to scale and the dimensions aren't critical. The rails are roughly 3/4" x 2 1/4" and the uprights are about 7/8" x 2" x 6 1/2". Centerline spacing of the uprights is 4", and centerline distance between pairs is 5". Minimum vertical spacing is about 14". If your clodhoppers are bigger than my size 10s, you'd want to increase these dimensions to suit.


Re: Getting organized

#2

So tell me....

Tim Greif - West of Chicago

>How'd you cut that 18 degree bevel on the bottom end of the tongue. I can see it being done on a table saw with an adjustable bevel jig but mine only goes to 15-degrees. Perhaps a CMS with the piece against a right angle jig?

Nice job.

Re: Getting organized

#3

Tenoning Jig.

Art Silva

>

Re: Getting organized

#4

Believe it or not

Ellis Walentine, Host

>... I bandsawed them. I had made sure that the blanks were quite square face-to-edge, then I marked them out quickly with a pencil and freehanded them on the bandsaw. I knew that the surface quality didn't matter since they were being screwed onto a board, as long as there were no egregious dips or bumps, which there weren't.

This brings up one of my favorite woodworking subjects: appropriateness.

The bandsaw just leaped out as the most appropriate way to make those cuts. I could have cobbled up a tenoning style jig, but it would have taken far more time than it took to bandsaw them by hand. Plus, unless my jig had a very positive hold-down, such as a substantial De-Sta-Co clamp or two, I wouldn't have wanted to try it on the tablesaw. The pieces are too short for my safety sensibilities. I considered a jig for the chopsaw, but the same concerns of finger proximity bothered me. I figure there's a reason why after 45 years of tablesaw experience I still can count to ten without using my feet.

If I were to get into production, it would be a totally different story. In a New York minute, I'd have a snazzy cutoff jig of some sort, more likely a tablesaw carriage than a chop saw solution. Hypothetically, I would probably use a mini-sled with an angled block to use as the angled fence. As long as there was something to catch the tip so it didn't get sucked into the kerf of the sled fence, i think I'd be comfortable enough.

Ellis

Re: Getting organized

#5

bandsaw tapers

John K Jordan

>I usually use the bandsaw for tapers and wedges, everything from cutting points onto stakes to cutting big wedges at small angles.

I just made some wedges from 4" thick white oak at about 5 deg angles to drive under a 40' shipping container for leveling. Besides the safest way to cut 4x10" tapers that I know of, the slightly rough bandsawn surface provides the perfect amount of friction for wedges.

JKJ

Re: Getting organized

#6

Quiet side is sometimes my method of choice

Stephen Kirk in Quakertown PA

>I've had a number of occurrences where I'll look at a cut and wonder how I can support that on the table saw, drill press, etc (I don't have a band saw yet!). If it's not a finish cut, oftimes I'll just grab one of my hand saws, bit brace, chisel, plane, etc. If I had to make a hundred of something, the time to build a jig is worthwhile. If I'm making only a few, a hand tool is quick and easy.

I learned a while ago to quit worrying about accuracy where it isn't necessary. I've learned to go sans jigs in a number of places, like routing out recess for hinge mortise - just mark the boundaries and get up close to them - finish with a chisel.

Thanks for sharing!

Re: Getting organized

#7

the Quiet side

John K Jordan

>Reminds me of the time about 30 years ago where several people spent a several frustrating hours trying to cajole an uncooperative software package into plotting a straight line in a certain place on a technical data plot that needed to go into a report.

I amazed them all - with a ruler and pen.

JKJ