Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

Jointing with a router

Posts

Jointing with a router

#1

Jointing with a router

Tom Dunlap

>Now that I have a shop setup to work in I can start on a project that I've wanted to make for a number of years.

The lumber came from a tree that I was paid to remove. Now I'm getting the 'oink out of the pig' by making something useful from the tree. The scraps will end up in my wood stove to get the last bit of oink.

In my lumber stack there are some 6/4 quarter sawn green ash planks. I had them milled with a wany edge to preserve the character of the tree. The first project will be a headboard.

The inside edges of the boards are angled because of the quarter sawn. My plan is to use my circle saw and edge guide to rough cut the edges. After the edges are squared up I'll need to joint them for a good glue up. Wrestling these big boards on top of my 6x48" jointer is not an appealing idea.

Years ago I read an article in FWW on edge joining with the router. In the article they showed how to setup adjoining pieces. The boards are clamped a little closer than the diameter of the bit so that a little wood is taken off both pieces in one pass. The base of the router rode on both pieces so any 'errors' are mirrored and would still glue up tight.

Would I be better off using a flush trim bit and a guide on the underside? This seems like a good idea because the end of the bit will be guided and not be deflected.

Does anyone have experience with a setup like this or suggestions?

The router I have is a Stanley Model 90150M with a 9 amp motor. Is this strong enough to do the job?

What style/manufacturer bit is recommended? Straight...spiral???

Re: Jointing with a router

#2

Re: Jointing with a router

Pat Evans

>If I were doing it, I'd use a spiral bit and clamp guides on both sides of the top to ensure the router doesn't wander. If the router were to wander from a single guide and you pulled it back, you would wind up with a gap. I'm not sure, but I think the technique you describe is intended for freehand routing. If your feed rate is slow enough, a small router will still do fine.

Re: Jointing with a router

#3

sure...

Bruce, a MN Galoot

>I have my router set up as a "jointer" as we speak, mounted in a router table. I just made a separate fence that uses a piece of thin laminate on the outfeed portion to create an offset. Adjust your bit to match the outfeed part and you're good to go. I use the biggest bit I have, in this case a 3/4" bit with 1-1/2" cutting length.

As a caveat, I'm not sure how well this would work on a really long chunk of wood, but for stuff up to 3' - 4' or so, it does just fine.

Bruce

Re: Jointing with a router

#4

Re: Jointing with a router

Clint Searl, at the base of Haycock Mtn

>I've done it the way you suggest with the exception that I set up a fence on one of the boards and used straight bits, plain and spiral. It's a fussy setup with fence, clamps, and a board under them, but returns a tight joint. With a router of your size, I'd use a 1/4 inch bit. Take time with the setup and it'll be fine.

Clint

Re: Jointing with a router

#5

Re: Jointing with a router

john lucas

>The way Pat says is the way to do it. I tried using one fence and the router moves on you since it's biting into both boards. I have since used my straight edge on one side and a straight board on the other to clamp the router into position.

Re: Jointing with a router

#6

I did that some years back

Bill Houghton, Sebastopol, CA

>with a Black and Decker router, about 9 amps, in oak. It worked fine, and gave a very clean edge to edge joint.

Re: Jointing with a router

#7

Re: Jointing with a router

Fred Davis

>Since you are getting the board edges fairly straight before jointing , think Table Saw instead of Router , much faster, and easier to set up.

We did this in on the job sites to eliminate bringing a jointer.

Simply clamp a thin piece of wood the thickness you want to cut off to the rip fence behind the cut , set for less then the saw cut kerf( we used 1/16") and your good to go.

It is also easier by far to use a straight edge held against the cupped rough edge of the board and run then both thru the saw , cutting off the crown on the opposite edge , which will give you a respectable edge to further refine.

FredD

Re: Jointing with a router

#8

1/4" bit???

Tom Dunlap

>Clint,

Do you mean a 1/4" diameter bit or shaft? My router will take a half inch diameter too. In an article I read about this type of setup they suggested a larger diameter to get higher cutting speeds at the tooth which yields smoother surfaces.

Re: Jointing with a router

#9

Big wood

Tom Dunlap

>Fred,

Using the TS was one idea. Since I'm working by myself and the boards are 6/4x11 +/- and 7-8 feet long I have a flat tree to wrangle. It seems easier to bring the horse to the cart in this situation.

What's your experience with jointing on the TS like you describe with big wood?

Re: Jointing with a router

#10

Re: Big wood

Fred Davis

>Tom , it's been years since I worked as a finish Carpenter on big interior trim jobs, but that setup will work well with any board you normally are able to rip on a TableSaw.

That being said I should have added a few more details.

Pick out a nice straight board about 12 inches longer and as high as the rip fence and 3/4" thick or so.

Either glue a strip on one half the length of the fence, the thickness you want to remove at a pass ( I use about half of the saw kerf) or remove that thickness from one half of the sacrificial fence.\

Remember that the jointing cut will be about half of the saw kerf , so the other half of the blade will be running in the sacrificial fence.

This is easy to do once you set the sacrificial fence on the half behind the blade so the blade barely touches the fence.

Then with the saw running , raise the blade high enough to clear your stock thickness and rip away or I should say joint away.

The size of the stock you quoted is certainly not more then one man could handle .

I just finished planing some 12/4 by ten inches about eight feet long Black Walnut and while heavy , I am not thirty years old either ;-))

FredD

Re: Jointing with a router

#11

Re: 1/4" bit???

Clint Searl, at the base of Haycock Mtn

>I used to do it with a lightweight Craftsman, and a 1/4" bit was less likely to bog down and easier to control.

Clint

Re: Jointing with a router

#12

Re: Big wood

Tom Dunlap

>Hahaha...I just turned 55...but I still climb the trees as well as I ever have :)

The weight isn't the issue really. It's moving the slabs around instead of having the wood sitting and moving the router instead.

The method that you described isn't new to me. There have been articles in mags that I've read. This is the first time that I've worked with such big stock.

There's a good chance that I'll use the TS for the whole works. Ripping off the wild edge may be easier with an adapted fence too.

This project won't start until the first of the month so I have time to mull things over.

Re: Jointing with a router

#13

Where Si the Router Lady when you need her?

Barry Irby

>A year or two ago I posted a question about doing something similar except that I wanted the joint to be a lazy S rather than be straight. Carol came back with a reference to "Cutting Sympathetic Curves," I think. I have two big slices of burl I want to join together to make a table top with a natural edge. Thought the curved joint would look better with the burl and natural edges. I was considering cutting both at the same time like you mention, but since there is a curve evolved, it won't work. Your idea would work because your edges are straight. OTOH, I'm not sure there is any advantage to doing both at the same time. Why not just joint two boards that match and would glue up nicely and clamp one to one board and joint the edge with the router and then do the other? Of course, if the board were really straight, you would only need one.

Re: Jointing with a router

#14

Routing curves

Tom Dunlap

>Last night I looked through my FWW 'Techniques 2" book and found the article.

The author, John Hanna, explains how to setup for doing slow or gentle S curves.

I can scan and email the article if anyone is interested.

Re: Jointing with a router

#15

One board at a time

Bill Hylton

>John,

You should joint the two boards in two steps to avoid the problem you cite. Set up and clamp the fence to a board and mill that board's edge with the router. Then bring the second board into position, establishing a gap between the two boards about 1/16" less than the bit diameter. Because the first board was milled on the first pass, the bit doesn't cut it on the second pass. It cuts only the second board, and because of that, you've got to reverse your feed direction.

See Woodworking with the Router (either edition) for a fuller explanation.

Bill

Re: Jointing with a router

#16

I meant to help you, now you are helping me

Barry Irby

>I would appreciate a copy of the article if it's not too much trouble.

Re: Jointing with a router

#17

Re: Where is the Router Lady when you need her?

Carol - now back in Dubuque, IA

>Well, the Router Lady is officially retired, but what you wanted to know is called complimentary template routing and detailed instructions are in my book "Router Joinery Workshop." Complete with great pictures and step by step instructions.

Sorry, been off-line for nearly two months. No internet connection where I was. Life can be tough!

Re: Jointing with a router

#18

Googlebooks:Router Joinery Wkshp. *LINK*

Tom Dunlap

>Take a look.


Router Joinery Workshop