Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Conundrum. Help please!

Posts

Conundrum. Help please!

#1

Conundrum. Help please!

Larry_Wyatt(Cole's Dad)

>I'm at a bit of a loss as to how to solve a problem so I thought I'd come to the great think tank on the web.

I'm building a clock(the one on the left with the inlay and arch)for my lovely wife. It will have a clock bored into a hole inside a round piece of cherry(??) and will sit on dowels inserted into the holes that you see. I was smart enough to bore the holes before cutting out the arch, BUT didn't test the fit of the dowels. Sooooooo, here I sit without a way to bore the holes a few thous larger. I know a Forstner bit would work, but the cupola of the arch would break I'm afraid, because of grain direction. I could sand it out, I suppose, but then the dowel fit wouldn't be good.

Feed me some great ideas, Seymour!!!

Larry Wyatt(Cole's Dad)

Houston, TX


img

Re: Conundrum. Help please!

#2

Re: Conundrum. Help please!

DouginDenver

>Can't tell exactly your problem, but what about using a lathe to turn the dowels slighly smaller just where they go in the holes?

Re: Conundrum. Help please!

#3

I'd try to resize the dowels

Gary Camp, Bend, Oregon

>I think I would drill a hole through a steel plate the size I wanted the dowel to end up and drive the dowel through it. That should shave just enough off the dowel to make it fit. At least I would try that first.

glc

Re: Conundrum. Help please!

#4

Re: Conundrum. Help please!

leadpipe58

>Can you sand the dowel to fit and shim the hole were the dowel fits in the clock?Just A thought. Good luck

Re: Conundrum. Help please!

#5

More info

Gary Camp, Bend, Oregon

>Do a google search for dowel sizing plates and you can get lots of information about commercially made plates that might guide you in making you own custom fit plate, like some relief on the back side and chammfer the leading edge of the dowel you are sizing

good luck

glc

Re: Conundrum. Help please!

#6

Agree with Gary

Ed Mulligan, Cape Cod

>

Re: Conundrum. Help please!

#7

Re: Conundrum. Help please!

john lucas

>As a turner I would of course just resize the dowels on the lathe. Lacking that you may be able to put them in a drill and resize them using sandpaper. I probably only need to resize part of the dowel to fit in the hole. If you taper it now one will know.

Re: Conundrum. Help please!

#8

Re: Conundrum. Help please!

Al Stokka - Cambridge, Iowa

>Larry,

Cut a piece of scrap wood to fit sungly between the arch sides (horizontally, as your part sits in the photo) in line with the holes. Then, drill away without tearout.

Al

Re: Conundrum. Help please!

#9

I did this last night!

Lee Schierer - McKean, PA

>I don't have a lathe and I needed a cylindrical piece of wood. I chucked it up in my drill press and used a bastard (coarse) mill file to re-size it. You can even make a step dowel if needed so the smaller end fits the holes in the arch and the larger ends fits the clock mounting.

Lee

Re: Conundrum. Help please!

#10

Re: Conundrum. Help please!

Robert Lemon - Sacramento CA

>Larry, Other than doing it the hard way, I usually shrink the end of the dowel by putting it on a hard flat surface, such as a TS or jointer. I then roll the end with a coarse bastard file. Use enough pressure to compress the wood.

Another method is to drive the dowel end into the closed end of a combination wrench or a 12 point socket. I just used the latter method this morning when constructing a push rattle cage.

Re: Conundrum. Help please!

#11

Many thanks for all the help, folks!!

Larry_Wyatt(Cole's Dad)

>