Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

14 " Band Saw question

Posts

14 " Band Saw question

#1

14 " Band Saw question

Frank in Forest Hill

>Gentlemen,

I just purchased a 1 1/2 hp 14 inch Delta Bandsaw

(475x") at the show in Baltimore 2 weeks ago. I was not

able to get it all put together until yesterday ( too

many other commitments)

When I tried resawing a 2 1/4 inch high piece of poplar

the blade drift on the supplied 1/4 inch blade it was

so bad I had to hold the piece about 1 and 1/2 inch out

of alignment with the blade to get a some what straight

cut.

I actually called the local vendor and asked what other

saws he had...thinking I could hand it back and move to

something that could at least handle a 6 inch high

resaw.

Went to the local Woodcraft store and bought some "cool

blocks" and a 5/8" inch skip tooth bland designed for

resawing.

The results were much better, with a 6 inch high, clamp

on fence, I was able to get a satisfactory cut. I would

still have to run it through the planer to clean up the

saw tooth marks, but it was about what I expected.

Are these the results typical on your 14 inch saw

or is this an "American hound" and I should get it

back to the vendor???

Re: 14 " Band Saw question

#2

JL

Re: 14 " Band Saw question

JL

>I would never try to resaw with a 1/4" blade. IMO, a 1/4" blade is used to cut curves, not resaw. You got the 5/8 blade, which is better as a resaw blade. I prefer a 3/4" (either Woodslicer or Timberwolf) dedicated resaw blade.

Re: 14 " Band Saw question

#3

Re: 14 " Band Saw question

slozuke

>Get a 1/2" Woodslicer blade and you'll be more than happy.

Re: 14 " Band Saw question

#4

A Good Read

Dave's Not Here

>Pick up a copy of Lonnie Bird's, The Bandsaw Book(ISBN 1-56158-289-1). It pretty much covers anything and everything you'll ever want to know about the bandsaw.

Re: 14 " Band Saw question

#5

Re: 14 " Band Saw question

Lee Schierer - McKean, PA

>Your results are about typical. Use a 1/2" or large blade when resawing as others have indicated.

Take a good look at your guides, particularly the one under the table and make sure it is free from slop. I added some UHMW tape to the slide on mine to take out the side play and it resaws much better. Run the cool blocks to the back side of the tooth gullets and tighen them so there is only a single piece of paper thickness between them and the blade on one side only. Make sure the roller under the table is actually free to turn. On my Delta the screw for the adjusting bar was loose from the factory. Tighening it made the roller bind against the slide frame. I ended up machining out part of the slide frame carriage to get adequate clearance for the roller when the screw is tight. Leaving the screw loose will result in it eventually falling out into the sawdust. DAMHIKT.

I have resawn to the full 6" height under the upper guide on several occasions. I run my blade slightly tighter than the indicator marks on the tension adjustment scale.

Lee

Re: 14 " Band Saw question

#6

Re: A Good Read

Frank in Forest Hill

>Tnank's for the information...... I googled The band saw book and dam if the illustration on the front cover looks just like the Delta saw. It sounds like the saw is OK , its' all in the blade choice, guides and adjustments.

Thanks for your fast response.

Frank on Chestnut Hill

Forest Hill Maryland

Re: 14 " Band Saw question

#7

Re: 14 " Band Saw question

Ed Mulligan, Cape Cod

>All good recommendations above. While you are waiting for your book and blade, here are a couple of things to play with.

1. When resawing, feed very slowly. Give the blade a chance to clear sawdust.

2. You can vary drift by adjusting the position of the band on the wheels. Aim to get the blade centered on top of the wheel. Some workers advocate using this adjustment to eliminate drift.

Ed

Re: 14 " Band Saw question

#8

Re: A Good Read

John K Jordan

>Also, you might try aligning the saw. I had to do that to my delta. The Duginski book has details.

Check where the blade is running on both the top and bottom wheels. If it is running significantly fore or aft of center, the blade may have a slight twist or toe-in or out, contributing to the drift.

I went too cool blocks as well, but after reading a hint somewhere I used a different method which seemed to work well for the way I mostly used the saw: cutting thick green chunks for woodturning (using a riser block). I kept the cool blocks on the outboard guides but replaced the original metal blocks on the inside. I tighten the blade and adjust the inner guides to rest slightly against the side of the blade, then adjust the cool blocks for some clearance. This tended both to keep the blade straighter and to keep some of the sap and resin from the green wood stripped off the blade.

Other things I did to the saw: add wheel brushes, a high-tension spring, a new tracking arm (from Iturra Design), better thrust bearings, and a Carter quick release.

JKJ

Re: 14 " Band Saw question

#9

It's the blade

Bill Tindall, E.TN

>As others have and will saw, many 1/4" blades are useless for resawing. I find a 1/2" 3 or 4 tpi blade to do fine.

Re: 14 " Band Saw question

#10

Re: It's the blade

Bruce, a MN Galoot

>I've had success with a good 1/4" blade, but it takes practice. However, the blades that Delta supplies are all but useless. Maybe for firewood or something, but as Bill suggests, get yourself a good quality Olson, Timberwolf, Lennox or some such blade and forget the Deltas.

For resawing, use a 1/2" blade. I once had a 3/4" blade but the saw couldn't handle the tension. I now run a Trimaster and it's wonderful but takes every bit of tension the stock springs can put out.

Bruce

Re: 14 " Band Saw question

#11

Re: 14 " Band Saw question

Jim Dillon

>Frank,

While I have the 10 year old 14 inch Delta, I think I have read that they have made a number of improvements in the newer model. Anyway, for resawing I have had luck with the 1/2 inch blades from Timberwolf (Suffolk Mfg), although for exotics like Jatoba I found the Lennox carbide blade to be exceptional with virtually no drift in resawing 10 inch planks - though I did have to feed very slowly. I keep the 1/4 inch for tighter curves and regular stuff. If Delta has not changed the tension spring, I would recommend buying a good one from Iturra or Carter so you can get decent tension on the blade. You've got a nice bandsaw that should serve you well.

Jim

Re: 14 " Band Saw question

#12

Re: 14 " Band Saw question

Ron Jones

>In case you haven't noticed the blade is the source of your problems. I've had good luck with the Olsen blades using 1/2 or 3/4 for resawing.

Good luck, and try either of the books suggested--there is much to learn.

Re: 14 " Band Saw question

#13

Re: 14 " Band Saw question

Frank in Forest Hill

>Thanks Again,

I bought the book, and am using a 1/2 inch Olson skip tooth blade...Much improved.

Amen!!!!

Re: 14 " Band Saw question

#14

Re: 14 " Band Saw question

Phil Thien

>Now try calling Iturra Design in FL (don't have phone # handy, let me know if you need it) and order some Blade Runner blades.

The Blade Runner is made from the same Atlanta Sharptech blade stock as the WoodSlicer from Highland Hardware. This blade won the FWW blade round-up. It is a thin-kerf, variable-tooth design. The thin kerf means less waste, and easier cutting. The variable-tooth design means less vibration (and less noise, a lot less noise, you gotta hear it to believe it).

Louis (Iturra) does outstanding welds, sells the blades for substantially less than Highland, and will include a approx. 200-page catalog that is a wealth of information on bandsaws if you order a couple of blades.

Highly recommended.

I have a 10" Delta benchtop saw and can cut 6" hard maple no problem. With a faster feed rate (if I want to) than most guys with big saws using lesser blades.