Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

On the utility of owning number drills

Posts

On the utility of owning number drills

#1

On the utility of owning number drills

Bill Tindall, E.TN

>Number drills are metal drilling bits that fill in the gaps of diameters between 0 and 1/4" not occupied by the fractional drill sizes. They are numbered 1-80 in decreasing size and they can be bought in sets of 1-60 and 61-80. It is a good bet that between the fractional drills and number drills one can drill a hole within 0.003", or less, of any diameter one chooses/needs.

I find them indispensable for woodwork. Take a recent example. I was installing Accuride drawer slides with flat head "sheet metal" screws. I used miscellaneous wood for the drawer sides and case so the screws were penetrating wood from oak to poplar in hardness.

With my digital caliper I measured the total diameter of the screw at 0.163" and the shank diameter (total diameter less threads) at 0.117". So ideally the pilot hole would be drilled 0.117" and it was a simple matter to find a number drill of this diameter. This diameter worked perfect for the softer woods. However, the oak was too hard for the entire thread depth to cut into it so the 0.117" pilot was too small. Using a scrap it was easy to find the right diameter for the oak pilot holes by trial and error. I use the same process to drill pilot holes for nails and brads. When installing hardwood trim I typically have three hand drills with number drills ideal for 16 ga. brads, #3 and #6 or 8 finish nails. The advantage is no split wood or bent nails because the pilot hole is too small.

If you only own a set of fraction drills the steps between sizes is too large to select a drill ideally suited for pilot holes. The result is too often wrung off screws or stripped slots. Ditto for brads and nails except here the bad result is too loose, bent nails or a split piece.

There are "letter drills" that fill the gaps in the fractional drills from 1/4 to 1/2" but I use these less. One handy use for them is fitting round tenons such as might be made on a lathe. I have a bad time hitting 3/8" exactly for example. Doesn't matter as some letter drill will match the actual tenon diameter.

Re: On the utility of owning number drills

#2

Re: On the utility of owning number drills

Clint Searl, at the base of Haycock Mtn

>I'll get a set when Billy May demonstrates them in an infomercial.

The last time I went to a woodworking show, I got suckered into buying a set of Bad Dog carbide tipped drill bits....they're useless!

Clint

Re: On the utility of owning number drills

#3

Re: Agree, but I like stubby bits.

Brian in Brighton

>OK, Maybe that didn't come out quite right.

The stubby bits I am referring to are known as "Screw machine" drill bits. They are 1/3 or so as long as standard "jobber" length bits. Once you try one, you'll never go back to jobbers until you need the length. Stubbies don't wander as easily, they don't flex and are quite a lot better than jobbers. IMHO.

Brian in Brighton

Just buy the 115 piece det from MSC and be done with it.

Re: On the utility of owning number drills

#4

Tennon sizing

Phil Joines in Krum, Tx

>Have you ever tried sharpening the long jaw of an open end wrench and using the short jaw to gage the cut? It works well for me as long as I keep the short jaw firmly aginst the wood.

Re: On the utility of owning number drills

#5

Wanna trade?

Henry Higginbotham

>My useless Bad Dog abrasive cut-off wheels for your useless Bad Dog drill bits? Do these guys have ANYTHING that works? They sure stink up the show with all that metal grinding, too.

Re: On the utility of owning number drills

#6

Re: On the utility of owning number drills

Brian Anderson

>As a gunsmith I walk the tightrope between being a woodworker and a machinist. I need and use both woodworking tools and machinist tools.

I find that I mix and match tools to perform a given task. I have one of those sets from MSC that has numberered, fractional and lettered drill bits. It helps a lot when attempting to match an odd dowel. But it is indispensible when performing tapping.