Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Bill Tindall - OK I made my sled, got questions

Posts

Bill Tindall - OK I made my sled, got questions

#1

Bill Tindall - OK I made my sled, got questions

Ed Beck

>Bill - I followed your advice and am building a sled that rides in both runners. I bought metal runners and attached them to 3/4" shop plywood (7-ply, birch veneered). I've got a piece of 5/4 ash that I routed over to make it comfy on my hands, glued to the plywood using Titebond III (that took a lot of time, making sure it was square).

A few questions.

1. I had what I thought was a good idea. My fence runs the full width of my sled (44") and has a blade guard on it. When I started to make the front blade guard I though, what if I make a back fence the full length also, then make a piece that I can put between the two fences. The purpose of this would be to have a fence that I could use for small (non-crosscutting) jobs. For example, cutting the lid off of a box. One might also be able to clamp the working piece to this fence as another way to keep your hands away from the blade. Good idea or bad?

2. Do I need to add some screws to the fence? I was planning on adding a few 2 1/2" #8 screws to each side of the fence. Is this overkill?

3. What about finishing? What do you typically use for this application? Something hard I would think.

4. Any opinions on what type of wax to use on the table saw and the sled? Or is this question going to start a religious war?

Thanks for all your help, I just hope that this thing cuts square, I'll find out tonight.

Re: Bill Tindall - OK I made my sled, got questions

#2

Re: Bill Tindall - OK I made my sled, got question

Fred Davis

>Religous war ?? I like that LOl LOL

Re: Bill Tindall - OK I made my sled, got questions

#3

A thought

roninkokomo

>I would not go to the trouble that you have without routing a semicircle in your sled on the side away from the blade so that you can make your fence adjustable to the various angles that you need. Really adds value to the sled IMHO

Ron

Re: Bill Tindall - OK I made my sled, got questions

#4

I'm not the font of sled knowledge

Bill Tindall, E.TN

>Your sled is way more sophisticated than mine. For others, 1/2" plywood is lighter and gives more blade height. There is a simple way to establish a fence square(perpendicular) to the saw cut. Recall from geometry how to make a line perpendicular to an established line, the established line being the saw cut across the sled. Establish this perpendicular line with a large compass or trammel and then attach fence to line up with this line. The result will be quick and perfect to a tiny fraction of a degree.

1. I don't know.

2. I wouldn't think so

3. Mine is not finished

4. I make my own wax. I melt pure Carnuba wax in xylene...... or I have been told that turpentine is an even better solvent for this application. I don't remember wax to solvent ratio. It needs to wind up a soft mush.

Re: Bill Tindall - OK I made my sled, got questions

#5

HOPE?? it cuts square

Pat Evans

>I hope before you glued the fence in place you were sure it cut square. Did you use the 5 cut method?

Re: Bill Tindall - OK I made my sled, got questions

#6

Re: Bill Tindall - OK I made my sled, got question

Keith Newton------WebKitFormBoundaryV6MZb+tiOpocz6

>More important than having the fence full length, is to make sure that it is tall enough that when you cut through it with the blade all of the way up, there will be plenty of wood left to hold it together for a little rough handling, if it gets dropped or falls over.

Some functions like cutting wide panels with an angle, call for more room by not being fenced in by a full length fence.

As for the suggestion of cutting an arc, I wouldn't bother with that. You can just make a miter gauge by putting a pin through a narrow board that fits into a hole near the blade slot. On the outer end, a drywall screw sticking through, and sharpened it to a very fine point, which stabs into the sled.

This will hold the outer end, since the work travels with the sled. Just insert the pen into the index hole, and stab the outer end into the sled where you want it. There is no need for knobs. This is a lot quicker. The pen near the blade slot is doing all of the work of countering the force of the blade against the travel of the sled.

If you strike an arc at 14 5/16" from the center of the pivot, then every 1/4" along the arc will be one �. However it is a good idea to establish 45� and 30 � 60�, 22.5� using geometry before stepping off the single degrees, because just being off a few thousandths adds up when you try to step it off with dividers.

Re: Bill Tindall - OK I made my sled, got questions

#7

Re: Bill Tindall - OK I made my sled, got question

Jim Dillon

>Ed,

<1. I had what I thought was a good idea. My fence runs the full width of my sled (44") and has a blade guard on it. When I started to make the front blade guard I though, what if I make a back fence the full length also, then make a piece that I can put between the two fences. The purpose of this would be to have a fence that I could use for small (non-crosscutting) jobs. For example, cutting the lid off of a box. One might also be able to clamp the working piece to this fence as another way to keep your hands away from the blade. Good idea or bad?>

For me, it is more important to have a nice full length and high rear fence (nearest the operator), than on the infeed side (further away from the operator). This way I can clamp blocks of wood for cross cutting things to the same length easily. My infeed fence is also full length, but not as high though high enough to not be cut entirely in two when the blade is fully raised. I'm dubious about the utility of a second fence parallel to the blade - if I understand what you want to do. For cutting the lid off boxes, I just hold the box against the rear fence and against a clamped block of wood to get a even cut all around the lid. IIRC Kelly Mehler fashioned some sort of "L-shaped" fence to clamp to the rear fence for providing stability to larger, taller items.

<2. Do I need to add some screws to the fence? I was planning on adding a few 2 1/2" #8 screws to each side of the fence. Is this overkill?>

Probably not, but a good glue up is your friend here. Just make sure the screws are not where the blade will cut through, and plan ahead in screw placement if you ever want to cut a 45 degree angle with your sled.

<3. What about finishing? What do you typically use for this application? Something hard I would think.>

All three of mine are unfinished, but waxed on the bottom. I'm not sure I would want a finish as I really don't want to increase the slipperiness (sp?) of the sled where it comes in contact with the wood.

<4. Any opinions on what type of wax to use on the table saw and the sled? Or is this question going to start a religious war?>

FWIW, I use the Renaissance brand wax. It is expensive, but very hard and a little goes a long way. I use it on the TS top as well. I have no experience with other waxes in this application, but other WC folk likely have. Hope this helps.

Jim

Re: Bill Tindall - OK I made my sled, got questions

#8

Re: HOPE?? it cuts square

Ed Beck

>Yes I did. Is 1/64" over 44" good?

Re: Bill Tindall - OK I made my sled, got questions

#9

Re: HOPE?? it cuts square

steve mackay

>A 64th ? ? ? Gosh. Lets call in the 'lectron microscope for a ruling . . . ROFL ! I get within an 8th and I'm REAL proud !

Re: Bill Tindall - OK I made my sled, got questions

#10

Re: HOPE?? it cuts square

Pat Evans

>I don't know. I can't measure that close.