Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

How do I drill a .13" hole?

Posts

How do I drill a .13" hole?

#1

How do I drill a .13" hole?

Barry Irby

>I'm making wooden hinges and bought a 1/8" brass rod for the pins. I drilled one and the rod won't go into a hole frilled with an 1/8" bit. Tried a regular twist bit and a split point. Then I tried a 9/64" bit and it looks like you could throw a cat in there with it. 9/64 is about .14". Looks like I need about .13" or just slightly over the .125 or 1/8". Where might I find a bit between 1/8 and 9/64?

I think I could drive the pin in with a hammer, but I don't want to split the hinges.

Re: How do I drill a .13" hole?

#2

Buy 3.3 mm bit

Alex Grigoriev

>

Re: How do I drill a .13" hole?

#3

Re: How do I drill a .13" hole? *LINK*

John K Jordan

>You might need to get a set of numbered/lettered drill bits. Number 30 is .1285" and number 29 is .1360". I have the set in the link - lots of sizes. But buy it elsewhere. (I'm boycotting Woodcraft)

Or chuck the pins in a drill press or lathe and file/sand to reduce the diameter a bit.

Or use one piece of rod (or a steel rod the same size), scratch or file some groves on it, and spin it into the wood as a reamer.

JKJ


115 piece set.

Re: How do I drill a .13" hole?

#4

Re: How do I drill a .13" hole?

Ken Oakley-Sunny St. Cloud, Fla.

>A number 9 bit,(.128), or a number 10 bit, (.136), are between 1/8" and 9/64". Any place that sells bits should carry numbered bits.

Re: How do I drill a .13" hole?

#5

#81 is 0.130"

Phil Joines in Krum, Tx

>

Re: How do I drill a .13" hole?

#6

OOPS- IMADE A MISTAKE,

Ken Oakley-Sunny St. Cloud, Fla.

>John has the right info.

Re: How do I drill a .13" hole?

#7

Re: #81 is 0.130"

Ken Oakley-Sunny St. Cloud, Fla.

>#81 is .0130 not 0.130---

Re: How do I drill a .13" hole?

#8

oops

Phil Joines in Krum, Tx

>

Re: How do I drill a .13" hole?

#9

every woodworker should own number drills

Bill Tindall, E.TN

>they are so handy for this sort of need as well as pilot holes for screws, nails etc.

Re: How do I drill a .13" hole?

#10

I got a number of drills.

Virgil J

>A number of them are dull...a number of them are pretty sharp. :-)

Re: How do I drill a .13" hole?

#11

Jim DeLaney, Austintown, Ohio

Re: every woodworker should own number drills

Jim DeLaney, Austintown, Ohio

>And letter drills, too. They fill in the gaps in a fractional set, up to just about half an inch.

Re: How do I drill a .13" hole?

#12

Re: every woodworker should own number drills

Tom MacGregor

>The bits you buy should be determined by what you plan to drill. Cheap 115 pc. sets, coated or not, often look great right up until the time you try to use them. Some numbers (ex.: tap drill sizes) are far more useful than others. You may want to buy good quality bits in just the few sizes you really need. Charts are available online with decimal equivalents for all common sizes. Look for an industrial supply that sells retail such as Fastenal or McMaster-Carr.

Re: How do I drill a .13" hole?

#13

Here's whatcha do...

Grant in Iowa

>Drill your hole undersized, but as close as you can to the final diameter.

Then take a length of the brass rod about two inches longer than the finished piece. File one end of the rod so it looks like a nail point. Chuck the other end into a drill and carefully use the rod itself to enlarge the hole. Once it is all the way through, test the function of the hinge to make sure it operates OK, then cut off the excess without removing the bit/pin.

I have done that a number of times over the years, should work fine so long as you don't mind a bit of resistance on the hinge in operation. If you do mind the resistance, you do the above procedure, then back out the pin/bit and take apart the hinge. Then do the following on the part that will move on the pin:

Take another section of the pin stock and point the end as above. Then tap flatten the end of the new bit ever so slightly against an avil, thereby making it slightly thicker. Use this to enlarge the holes which are to rotate on the pin. If flattening the tip slightly doesn't yield satisfactory results, then try just biting down on the rod with a pair of pliers or vise grips until marks are raised in the stock. These marks will make the rod drill a slightly larger "clearance" hole.

I think this would work so long as you are making wooden hinges from all but the hardest of woods.

of course you should try this on a sample piece/ hinge first so you don't "pooch" the real part!

Regards,

Grant in Iowa

Re: How do I drill a .13" hole?

#14

Re: Here's whatcha do...

Lee Schierer - McKean, PA

>I've done similar things by filing a notch or two length wise at one end of the rod so it sort of resembles a drill flute. Flattening the rod slightly will make the hole slightly large than the rod.

Lee

Re: How do I drill a .13" hole?

#15

Re: every woodworker should own number drills

John K Jordan

>>Cheap 115 pc. sets, coated or not, often look

>great right up until the time you try to use them.

Well said.

I think the value of a set like that is for that occasional need for a special size - with an occasional use a quality set will last indefinitely. For those unusual sizes that get used a lot, I buy them individually.

For most drilling, I use bits from a couple of HSS sets like this (image below) that has multiple bits of each of the common sizes. I bought them in both brad and normal tip. These are available from Woodcraft and pretty cheap when on sale. (but buy from anywhere but Knoxville Woodcraft)

JKJ


img

Re: How do I drill a .13" hole?

#16

disagree with this aproach

Bill Tindall, E.TN

>1. After the purchase of a few bits you will have spent the price of a set.

2.Over the years I have used well over half the sizes in a number set for - pilot holes for screws, tap holes, pilot hoes for nails in hardwood, holes for inserting brass wire into turned Christmas ornaments and a multitude of other things. I like the idea of having a tool when I need it and when it comes to drill sizes I have not been very prophetic when it ocmes to know what I need next week. It is not like a set of number drills 1-80 cost very much.

3. Number drills coupled with a machinist caliper( so you know what size is needed) ( I prefer digital) is the winning combination.

Re: How do I drill a .13" hole?

#17

Ellis Walentine

Cool advice, Grant

Ellis Walentine

>I want to know more about tap flattening.

I've modified all kinds of bits over the years for various things including tapered holes, but I've never tried your technique for small increments. Good one

Ellis

Re: How do I drill a .13" hole?

#18

Clarification:

Grant in Iowa

>What I call tap flattening will only work on a malleable metal like his brass hinge pins.

Lay the newly pointed tip on an anvil and tap it with a hammer such that the end widens slightly.

I should add that filing or grinding a flute or two wouldn't hurt if the first hole is much smaller than the finished hole size as mentioned.

Learned it by watching my dad "spin" finish nails into trim work back before many people had air nailers. If he was using a given size nail, he'd cut the head off of one and install it in the drill to make a pilot hole to prevent splitting the workpiece. And he'd even flatten the end a bit to make the hole a bit larger, if needed.

Anyway, it was one of his old Belgian/ German carpentry tricks....not that they had electric drills, mind you.

FWIW,

Grant in Iowa

Re: How do I drill a .13" hole?

#19

Re: Clarification:

Fred Davis

>Every Cabinet maker and Finish Carpenter used the same nail size for a pilot hole bit with the head snipped off, before air nailers came along.

And I bet if you were watching closely , you would have seen your Dad blunt the end of the finish nail he was driving to prevent splitting the wood, or any nail for that matter that was driven close to a edge, end or in hard wood.

In addition many Carpenters who used a wood handle hammer had a hole drilled in the end of the handle and loaded the hole with bees wax.

To lubricate a nail he stuck the tip of the nail into the wax and enjoyed split free nailing .

Some of the Framers I used in California dumped some ivory soap flakes in their nail belt pockets , which gave them the ability to drive a 16 penny nail with one stroke of the hammer.

Some even used a exotic mix of wax and gasoline dumped into a fifty LB. box of nails for the same reason.

Many building inspectors frowned on this practice , because it reduced the withdrawal force necessary to pull a nail .

But the Framers with the Ivory flakes approach had the nicest smelling tool belts and really clean hands . ;-))

FredD

Re: How do I drill a .13" hole?

#20

Re: How do I drill a .13" hole?

Well just hurry up....

>Drill with what ya have, then chuck the pin in the DP and "spin" it into the drilled hole.

Bill