Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

WC Weekend Accomplishments....

Posts

WC Weekend Accomplishments....

#1

WC Weekend Accomplishments....

Dennis E. Peacock

>5 Jan 2009

Wow.!!! Where did 2008 go????

I didn't get any woodworking done last week due to being oncall for the day job. I can say that I am truly thankful for still having a job as many that I know are desperately looking for jobs from the various companies that have been laying off near here.

I found out last week that pulling 28 hours straight isn't as easy as it used to be and recovering from working long hard hours like that isn't easy either. Just takes longer to recover is all.

Been thundering here this morning and rain is starting to fall. Current temp is 31� F with a high today of 38� F. Who knows what the weather will bring us today, but....at least I'll be in the shop today.!!!

That's it for me....so what did YOU do this weekend??

Best of weeks to you all.

Dennis Peacock

Re: WC Weekend Accomplishments....

#2

I actually did some woodworking......

Andy Halterman: 30s officially over

>albeit very little.

Sat. was ride day. Cut short since my buddy discovered a nasty crack in his bike frame. Not too bad since it was threatening rain.

Sunday I cut and split firewood for most of the day. Took off on the road bike around 4:30 and rode until dark. Did some dinner and then whipped out materials and made up four cutting boards for gifts. I slept very well last night. :-)

Andy Halterman

Easing into another work week in Hendersonville, NC�

Re: WC Weekend Accomplishments....

#3

Alan Young

Working on Mt Media Wall

Alan Young

>I am making progress on a project that seems to have no end. This weekend I installed the first level of bookshelves on the Media Wall.


This project is made from Sapele veneers and Hardwood. The right side poses numerous challenges with the ceiling angle and the window on the adjoining wall.

This week I am working on the next level of bookshelves-These will complete the right side and just extend over the ledge on the left side.More odd cuts and angles. Measure 30 times and make sure I can read my notes before cutting!


The final round will run to the top of the cathedral ceiling on the left side.


Alan

Re: WC Weekend Accomplishments....

#4

made shuttles from dogwood for a loom

John K Jordan

>

Re: WC Weekend Accomplishments....

#5

Several firsts for me

Don Orr

>Since I am mostly a turner, I had several firsts this past weekend. I had Friday off so it was a long weekend for me. I am in the process of building my first real cabinet. I need something to hold my planer and can use the storage below it. I have the Kreg pocket hole jig to use in the construction. I cut the sides after carefully checking my dimensions and they came out well. Now for some firsts-In order to make the rabbet for the back panel I used a stacked dado blade in my tablesaw. I have had the blade set for about 3 years waiting for something to use it for. They�re not very useful in turning ;-) In order to use the dado blade correctly, I needed to make a zero-clearance insert for the TS. I did this successfully by using the standard ZCI as a pattern and a flush trim bit in my router-another first for me-pattern routing. Came out great and worked perfectly with the dado blade. I also made the top frame and floor for the inside of the cabinet and they are even the same size ! I know this is not a big deal to most of you but it is to me. Not bad for a round guy who wants to go flat too.I now have to make the face frame and door and drawer. Off to a good start for the new year !

Re: WC Weekend Accomplishments....

#6

Re: WC Weekend Accomplishments....

George@Colonel's Workshop-Havertown PA

>Good Morning Dennis, and a Happy Monday,

I am almost bored to death in the shop. One can only clean it so much! I worked a little on my table saw top to polish the iron and rid it of stains. Then I began finish on two bowls, and noticed one of them had "turned" into a crownless cowboy hat. The headboard and footboard to the Master Bedroom Suite await strong, sustained sunlight, so that project is suspended in winter's icy grip until spring. I did manage to apply some finish to the infed and outfeed areas of the new SCMS. Charlie is coming over later this week to dimension some poplar and turn replacement spindles for his SIL's chair. We may continue with lathe work on bowls. We have a large accumulation of wet bowl blanks, and need to get them once turned. Had a small dinner party last night during the Eagles game, but did get to see highlights on the news. Those Vikings have the power to explode at any given second, and I was surprised by the final point spread.

Have a great week, Dennis.

George

Re: WC Weekend Accomplishments....

#7

Re: WC Weekend Accomplishments....

Winnemucca Lynn

>Went to Reno (2 1/2 hour drive each way) on Sat. to take a Woodcraft course in beginning carving. The project was supposed to be a boot. Unfortunately, mine turned out to be a muk-luk. Still, it was a fun time.

Lynn

Re: WC Weekend Accomplishments....

#8

Ellis Walentine

Took the weekend off

Ellis Walentine

>LOML and I wanted to see the VanGogh show at the Museum of Modern Art before it went away (today is the last day of the show), so we googled around for hotel deals. Sure enough, Candy found a real deal on a room in midtown Manhattan and we drove into New York Saturday morning for two exhausting days of gallery hopping, museum shows (including VanGogh -- not as good as we had hoped), a Broadway musical and a couple excellent meals, including burgers at what has been called the best burger joint in the country. (They really were excellent.) I hadn't been to NY in a while and was floored by the prices they charge for stuff -- can you believe $8 for a cup of coffee, $9.70 for a toasted bagel? So, we cabbed across town to the low-rent district where we had bottomless cups of coffee and excellent bagels for about $4 total. Whew.

Anyhow, one of the galleries we went to had a piece of furniture that looked familiar. Sure enough it was a coffee table by Silas Kopf with bog-oak "oysters" inlaid in the top. We didn't have time for other woodworking-related forays, though, and I knew better than to haul Candy into Tools for Working Wood. I dragged her to Silvo Hardware in Philadelphia 30-odd years ago on the first day of our honeymoon. If you think an extension ladder is a bad anniversary gift to your wife, take my word for it: tool shopping on a visit to the Big Apple is much worse.

Anyhow, now we're back in the saddle and looking forward to starting 2009 with a positive attitude and as much energy as these tired bones can muster.

Ellis

Re: WC Weekend Accomplishments....

#9

Thawed out in Milton, FL

Dave Smith, Longview, WA

>After a freezing on a winter passage from Longview, WA to Indy we went straight South for some 70 degree weather. Heading to Houston, TX on Wednesday. Haven't decided the route from there to Mesa, AZ.

I brought my pen making supplies but forgot the mandrels. Good thing I don't turn for a living.

Dave Smith

Driving Miss Sandy

Three thousand miles from my shop in Longview, WA.

Re: WC Weekend Accomplishments....

#10

Made two shoulder planes

Steve Kreitler

>Promised my SIL a shoulder plane for Christmas, and finally got around to it. Since I had two blades, and don't like to just make one of anything, I made two of them at the same time (yep- one for me, too :).

The design is from the Aug/Sept '08 Woodcraft, body is white oak (from a solid frame door I salvaged a few years ago- parts of it went into my workbench, too), the sole is purpleheart (from a piece my MIL gave me many years ago). The blades are cut down flat Unitool Chisel blades that I got at garage sale last year for a quarter each (lots of patience with the dremel, there- kind of a Zen thing). Width is 5/8".

These are the first planes I have made, and it was really enjoyable. I'm sure I'll find lots of uses for mine, since I like to make small items.

My technique in making them was different from the author's- he used the tablesaw to cut wide, shallow rabbets for the sides. I happen to know the the fence on my table saw is a couple of thousandths out of square, and I didn't like the chance of my thin kerf blade flexing while cutting these rabbets, so I used the router table instead.

I ripped the piece for bodies to the correct width, glued on the sole, then made the cuts for the mouth openings. I then ripped some long strips from scrap, and glued the bodies between the strips, aligning the pieces carefully. Then it was through the planer to flatten and bring it all to the desired width. Leaving the planer setting undisturbed, I used a 3/4" straight bit on the router table to cut the rabbet on one side at a time (setting the depth of cut so that the side would end up slightly proud of the body). Glued on one side, and ran it through the planer, then did the other side.

Using the scrap strips made it very easy to plane my workpieces to width, and making them long prevented any worries about snipe in the plane bodies.

I used my scroll saw to cut the final shape and also to cut out the mouth opening.


img

Re: WC Weekend Accomplishments....

#11

Finished up Trim

Mike Fitterling

>Installed all the cypress trim in the addition and only have a few pieces of cherry trim to go in still in the office. I milled the cherry up throughout the weekend and it is all lacquered and sitting in the office waiting for me to have some time to finish installing it. Next up 12 drawers; nine large sames sized ones for the bath cabinet and three smaller ones for the vanity. Going to get my practice in on handcut dovetails with these.

Cheers,

Mike

Re: WC Weekend Accomplishments....

#12

Re: Turning Black Acacia

Glenn Madsen near San Francisco

>is more of a challenge than I'd expected.

The blank, fresh off the firewood pile, looked green, but turned dry. And dulled the tools at an amazing rate, too.

I quit when my back cramped up due to the cold, but three or four hours at the lathe in January, even in California, is a bit much. There's probably another couple of hours of work to do on this, and it's only about 9" in diameter...

It WAS good to get some more done, though.