Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Compound off-angle mortise help

Posts

Compound off-angle mortise help

#1

Compound off-angle mortise help

JohnM in Mid Mich

>This holiday I made as presents a few ceviche (citrus marinated raw fish) servers like shown in the picture (this one in lightly spalted cherry). SWMBO wants more to give away (especially one for friends who go to Alaska for halibut every summer). Mortising the legs into the top for the first batch of these was a bit tedious and I'm hoping somebody has a simpler idea for how to do it. The legs are canted out at 15 degrees and are tapered on both sides also at 15 degrees, and these are mortised into the top as shown in the detail at the bottom of the pic. I cut the mortises on the table saw using my miter gauge: I mounted an auxilliary fence with a 15 degree sloping face, and angled the miter gauge at 15 degrees one direction, then 15 in the other direction. This gave me the right mortice, but like I said, it was a tedious process. How would you do this?


img

Re: Compound off-angle mortise help

#2

Re: Compound off-angle mortise help

George@Colonel's Workshop-Havertown PA

>Those look pretty nice to me, John

Sure its tedious, but hard to argue with the results. About 30 years ago, I would have made a maranade of 3 parts gin and one part vermouth, and set in an olive or two to soak. After several of them, shaken, not stirred, I'd form my own compound off angle with no trouble at all. Good work.

George

Re: Compound off-angle mortise help

#3

Dovetail saw?

Alexander Grigoriev

>

Re: Compound off-angle mortise help

#4

Hey Colonel, Do you marinade the fish?

Keith Newton------WebKitFormBoundaryV6MZb+tiOpocz6

>It sounds like you were marinading yourself, so you wouldn't notice when you had a bone hung in your throat. Ha,

Oh well, whatever works.

Back to the OP's question. Why don't you think about doing a finger joint corner for that splayed leg joint. You can do a set-up on a TS sled, with large fingers that you can knock out multiples pretty fast, that will be strong enough to park a car on, that will look nice too.

Re: Compound off-angle mortise help

#5

Re: Hey Colonel, Do you marinade the fish?

JohnM in Mid Mich

>I believe what he was describing was marinading the woodworker! Although, maybe drinking like a fish qualifies also?

Re: Compound off-angle mortise help

#6

Re: Compound off-angle mortise help

JohnM in Mid Mich

>Ah, so you recognize the design purpose for the glasses, eh? These are sold as "stemless martini glasses", but were pretty close to what I was looking for. If you ever get a chance to have ceviche at Rick Bayless's "Topolobampo" restaurant in Chicago, you will recognize the design inspiration (if it is still on the menu).

Re: Compound off-angle mortise help

#7

Ellis Walentine

I'd make a dovetail markng template

Ellis Walentine

>... and cut one shoulder on each edge of the leg and a dovetail angle on the tops of the legs and in the top. Once you have the marking out under control, you can use hand saws and a bandsaw to hog out the sockets. If you want to go into some kind of limited-production mode, you could make a couple router jigs and just rout out the dovetails. I wish I had time to write the whole instruction sheet for what I'm talking about.

Ellis

Re: Compound off-angle mortise help

#8

Re: I'd make a dovetail markng template

JohnM in Mid Mich

>So, I thought about hand cutting them, but my atrophied brain could not, for the life of me, calculate the angles. I know that it is 15 degrees, both ways, but my geometry failed me on getting the combo. What I mean is, if you are looking straight down on the joint, the shoulder cuts are NOT 90 degree to the end of the board. Take a close look at the detail in this pic. This angle is not 90. I can measure it now that it is cut, but d&#@ me I can't calculate it. And if I can't calculate the angle, how do I lay it out correctly?


img

Re: Compound off-angle mortise help

#9

Re: I'd make a dovetail markng template

Alexander Grigoriev

>First cut the leg with all the correct angles. Use the leg to mark the top.

Re: Compound off-angle mortise help

#10

Re: I'd make a dovetail markng template

JohnM in Mid Mich

>I agree that sounds simple, but, well, it isn't exactly possible. There are 15 degree bevels all around. You can fake it by a bunch of moves, but because of the angles, you can't just place the leg on and mark. Believe me, I tried it. Think about those angles. If I try to place a leg on, I've reversed and flipped it, reversing the very angle that I'm having trouble with. It is a bit hard to describe. I would almost suggest trying this exact cut to see what I mean.

Re: Compound off-angle mortise help

#11

Re: I'd make a dovetail marking template

Dan Donaldson

>I believe that the angle is about 12� You can use the miter calculator that was posted a couple of days ago and use 105� for the corner angle and 15� for the other. I did that and got 11.8� . I then calculated the distance as in your picture for the odd angle and got that the offset would be around .1 inches, which is at least fairly reasonable from the view in your picture.

For myself, however, I think that I would cut one joint the way that you did before, get it to fit the way that you want, then use that as a template to create a marking gauge to make the rest.

Re: Compound off-angle mortise help

#12

Re: Compound off-angle mortise help

JohnM in Mid Mich

>Thanks everyone. I guess there is no "silver chisel" here, as the consensus seems to be that I will have to work more or less empirically. Last night I made a jig for the router table that worked much better than the table saw, though it was basically the same concept: 15deg sloping face, 15deg angle to the right, then left, then clean up down the middle. Check the fit on a leg until it is good enough, clamp on some stops, and make the rest of the cuts.