Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Common tools defined

Posts

Common tools defined

#1

Common tools defined

John Luke

>COMMON TOOLS DEFINED

DRILL PRESS: A tall upright machine useful for

suddenly snatching flat metal bar stock out of your hands so

that it smacks you in the chest and flings your beer across

the room, denting the freshly-painted vertical stabilizer

which you had carefully set in the corner where nothing

could get to it.

WIRE WHEEL: Cleans paint off bolts and then throws

them somewhere under the workbench with the speed of light.

Also removes fingerprints and hard-earned calluses from

fingers in about the time it takes you to say, "Oh crap..."

SKILL SAW: A portable cutting tool used to make studs

too short.

PLIERS: Used to round off bolt heads. Sometimes used

in the creation of blood-blisters.

BELT SANDER: An electric sanding tool commonly used

to convert minor touch-up jobs into major refinishing jobs.

HACKSAW: One of a family of cutting tools built on

the Ouija board principle. It transforms human energy into

a crooked, unpredictable motion, and the more you

attempt to influence its course, the more dismal your future

becomes.

VISE-GRIPS: Generally used after pliers to completely

round off bolt heads. If nothing else is available,

they can also be used to transfer intense welding heat to the

palm of your hand.

WELDING GLOVES: Heavy duty leather gloves used to

prolong the conduction of intense welding heat to the palm of

your hand.

OXYACETYLENE TORCH: Used almost entirely for lighting

various flammable objects in your shop on fire. Also

handy for igniting the grease inside the wheel hub out of

which you want to remove a bearing race.

TABLE SAW: A large stationary power tool commonly

used to launch wood projectiles for testing wall integrity.

E-Z OUT BOLT AND STUD EXTRACTOR: A tool ten times

harder than any known drill bit that snaps neatly off in bolt

holes thereby ending any possible future use.

BAND SAW: A large stationary power saw primarily used

by most shops to cut good aluminum sheet into smaller

pieces that more easily fit into the trash can after you cut

on the inside of the line instead of the outside edge.

TWO-TON ENGINE HOIST: A tool for testing the maximum

tensile strength of everything you forgot to disconnect.

CRAFTSMAN 1/2 x 24-INCH SCREWDRIVER: A very large pry

bar that inexplicably has an accurately machined screwdriver tip

on the end opposite the handle.

PHILLIPS SCREWDRIVER: Normally used to stab the

vacuum seals under lids or for opening old-style

paper-and-tin oil cans and splashing oil on your shirt; but can also be

used, as the name implies, to strip out Phillips screw heads.

STRAIGHT SCREWDRIVER: A tool for opening paint cans.

Sometimes used to convert common slotted screws into

non-removable screws.

PRY BAR: A tool used to crumple the metal surrounding

that clip or bracket you needed to remove in order to

replace a 50 cent part.

HOSE CUTTER: A tool used to make hoses too short.

HAMMER: Originally employed as a weapon of war, the

hammer nowadays is used as a kind of divining rod to locate

the most expensive parts adjacent the object we are trying

to hit.

DAMMIT TOOL: Any handy tool that you grab and throw

across the garage while yelling 'DAMMIT!' at the top

of your lungs. It is also, most often, the next tool that

you will need

Re: Common tools defined

#2

Re: Common tools defined

Sawman

>SOOO TRUE!!!

Re: Common tools defined

#3

Hijack, Primitive Pete

Randy Johnson Connersville IN

>Yesterday I kept hearing something that sounded almost, but not quite, like a series of gunshots. Investigation showed that a neighbor was putting holes in the bottom of a 55 gallon drum using an old screwdriver for a chisel.

Somewhere in our conversation, Primitive Pete came up.

I'd guess that at least some of you who took shop class in the 40s, 50s, and 60s were exposed to Primitive Pete. He was born at the Walt Disney studios during WW II to teach GIs the proper (maybe I should say IMproper) use of tools. Pete was always using them in a fashion the Army considered incorrect.

However.....

Among my dad's "war stuff" was a companion book that went along with the movie I saw in 7th grade. Looking through it I was a little shocked to discover that, as an adult, I am a Primitive Pete. I occasionally use a screwdriver for a rough chisel job or to pry with. Very occasionally. I have been known to use an adjustable crescent in conjunction with a square shank screwdriver to get more leverage and have slipped a pipe over a wrench handle for the same reason more times than I can even begin to remember. I HAVE been able to refrain from using a file as a pry bar, but for the most part, if I had NEVER done any of the things forbidden by the creators of Primitive Pete some jobs would have been a lot harder if not impossible.

I�d bet Stanley worked with Disney to create Primitive Pete. They did it to sell more tools.

Re: Common tools defined

#4

Re: Common tools defined

Bill White

>John, You now owe me a new lap top as I have sprayed coffee ALL OVER the keyboard. Too funny.

Bill

Re: Common tools defined

#5

The original, and better, version

Rod Peterson -- Ormond Beach

>

The Right Tool for the Job by Peter Egan, “Road & Track”, April, 1996


Rod

Re: Common tools defined

#6

Good catch Rod, and a reminder not to forget.....

Art Silva

>the "Attribution Rule". Mr. Egan's work has graced the walls of many shops, both auto and wood, for many years, and has been the cause of many belly laughs.

Re: Common tools defined

#7

I actually got permission…

Rod Peterson -- Ormond Beach

>…from Road & Track to post it on my website. Of course that was several years ago, and ownership of copyright was a little murkier then (at least to me). I might should contact Egan and get it from him, too.

Rod

Re: Common tools defined

#8

Re: I actually got permission�

Lynn Baker in snowy Glacier, WA

>Rod,

Thanks for showing the list again. I actually saw it for the first time in R&T long ago. For me, the most apt and hilarious description is for the trouble light. I think that most of us, at some time, have used up every bulb in the house in an extremely short time trying to finish a job.

Thanks Again.

Lynn