Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Need help with dial indicator

Posts

Need help with dial indicator

#1

Need help with dial indicator

Jeff H. - Oregon

>Been snowed in the last few days so taking adavantage of being at home and giving my table saw a tune up.

Running into problems and I think it is the dial indicator but not sure.

The dial indicator was working fine and the results on arbor runout (0.002"), blade runout (0.005") and blade parallel to miter slot (0.003") were about what I expected. I used a magnetic base with the dial indicator.

The problem I encountered was when I moved to the fence to adjust parallel to the miter slot. I keep getting odd readings. I would zero out the indicator at the front of the fence. The gauge would dip to about -0.007 in the middle of the fence and then go to +0.003 at the back end of the fence. Moving the gauge back to the original position and it would be 0.003" off. I checked the fence face with my straight edge and it to be true. I went back and redid my original testing and now found the readings to be about 0.005" off from when I originally tested.

I have not dropped the dial indicator. This is a harbor frieght $14.99 special. Did I go too cheap? Is it operator error?

Re: Need help with dial indicator

#2

Re: Need help with dial indicator

Marvin Horn

>I assume you're mounting the indicator on your miter gauge and traversing the fence. Slop in the runner of the miter gauge can give you readings like that. I've always had better results by inserting a tight fitting 3/4" board in the miter slot and using feeler gauges to adjust the fence to parallel or whatever offset you're trying to get. Not as high tech but simple, accurate and repeatable.

Re: Need help with dial indicator

#3

Hard to tell.

Forrest Addy

>Hard to tell from your narrative. There may be information missing even though you made an effort to be thorough. A long skinny item like a table saw fence is affected by heat same as any otner object but being long unqualized heat has more effect. In handling the fence to test it parts of the fence expanded and parts didn't making an irregular curve. That may be why you got inconsistent results.

Try it again but this time use gloves to protec the fence from heat transfer and see of you don't get more consistent readings.

Re: Need help with dial indicator

#4

Loose fit

Lee Schierer - McKean, PA

>I suspect your miter gauge is loos in the slot on your table. With the dial indicator at one point, intentionally move the miter guage left and right and see what the dial indicator does. I suspect you will find your .003 or possibly more.

I was able to eliminate all the play in my miter guage by sticking some .004 thick UHMW tape to teh side of my miter gauge bar. It fills the gap and makes the bar slide like it is greased. The tape will last far longer than center punch pricks along the sides.

Also seeing variation in the length of the fence is not all that unusual. Once you get your reading variance straighted out it may be necessary to shim the fence to get it flat along the length.

Lee

Re: Need help with dial indicator

#5

Some one make them stop...I can't stop laughing!

Chris Knob

>Ok OK OK I'm a scarcastic a-hole!!! 0.003" on a piece of woodworking machinery? Don't touch it with your bare hands because the heat from them might be causing the metal to warp???

I've got an 8" wide piece of oak in my shop that's probably 1/16" narrower on this dry as a bone Monday as it was on a sopping wet Friday and you guys are sweating 3 mils???

Look, I love dead on accuracy when it comes to my machinery but there is a point of diminishing return when one is working wood. Metal, that's another story but I think your fence is beyond as straight as it needs to be.

Re: Need help with dial indicator

#6

Miter Slot Bar use and other info

Jeff H. - Oregon

>I am using a miter slot bar I purchased from Woodcraft. I have bolted the dial indicator to this bar. Similar results using either this bar or the miter guage.

I agree with Chris and do not care much about the 0.003" but I just purchased a Beisemeyer fence and installed it this weekend. Since I have to align the fence I wanted to align everythign else. The fence is about 0.011" off total. Not a lot but I prefer to have this set up to prevent any kickback.

I had a kick back a while ago. I am tall enough that the kick back hit me in the area that turned me into a soprano. I am going to do everything I can to prevent a repeat including changing my stupidity.

Re: Need help with dial indicator

#7

Best kickback insurance

Chris Knob

>Any your Bies will let you do this...toe it out about 1/128" away from the blade. It will make a neglegible difference in the width of your rips (Ok they'll be 1/512" strong)and the quality of your cuts and you will have reduced your blade/fence binding issues to almost zero.

Re: Need help with dial indicator

#8

Re: Best kickback insurance

Bill White

>I gotta agree with Chris.

I have my fence set with a small relief toward the back of the blade, and I have not had any probs yet. Sometimes we get too carried away with the perceived need for +- tolerances. I don't think that any of the old masters used dial indicators. Rember that wood "WIGGLES" with each change in the weather.

Bill

Re: Need help with dial indicator

#9

Re: Best kickback insurance

Glenn Madsen near San Francisco

>My best kickback insurance came from Lie Nielsen, and says Independence Tool across the back of the saw...

I may have a tool to measure to .003". Somewhere. If it hasn't rusted.

Re: Need help with dial indicator

#10

There is a boys choir somewhere that wants you.

Keith Newton------WebKitFormBoundaryV6MZb+tiOpocz6

>As for toeing the fence out as someone suggested, I don't bother with that. Most of these T mounted fences have some flex as you apply the pressure of feeding, and the pressure is greater as you get closer to the end of your cut.

I just put a dial indicator on the back my delta fence on 0, then pulled against a scale. At 5 #, it moved .010, and with 10# it was over .015".

You should keep this in mind as you are finishing your cut. Never stop feeding a part until it is clear of the back of the blade. If you are using a lot of pressure into the fence, maybe from fear of a kickback, then stop short of pushing it clear of the back of the blade, the spring action of the fence returning to its resting place could kick the work onto the back of the blade, and initiate a kickback.

Re: Need help with dial indicator

#11

Re: Need help with dial indicator

Brian in Brighton

>Slap the plunger a couple times and see if the needle moves around the dial face at all. With these cheap dial indicators the needle will sometimes move on the post. If it does, you can carefully pry off the bezel (plastic face) and with a very small tool push the needle back onto the post a little tighter. I used a very small hex socket tool from my tiny screwdriver set (one of those kits you get from the big box store). You want to make sure you don't hit the post, just the needle. Slap the plunger a few more times. If it still wants to move you can try to super glue the needle to the post. Basically it should not move on the post, which is what it sounds like might be happening.

You can hold onto that metal until the cows come home and it's not gonna move .003 inches. Not a small change like even 0-100 degrees will make small amounts of metal move like that.