Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

small hinge source

Posts

small hinge source

#1

small hinge source

John E in SC

>My recent "quick and dirty" weekend project turned into a major pain because of some el cheapo brass hinges. #2 son (6 years old) was upset recently 'cause he couldn't find a suitable box to put his "rock collection" (gravel picked up from the playground at school) in. That reminded me too much of myself when I was his age, so being the respectable Dad that I am, decided, "No problem, we'll make you a box!" I had taken a class on handcut dovetails recently, and needed a good excuse to practice anyway. Fashioned a nice little box with dovetails out of some red oak. All went smoothly, until I tried to put a couple little brass hinges on the lid. I had had them lying around for some time, and I really don't even know where they came from. Problem is, I ended up making a huge mess of my cute little box. No matter what I tried, including predrilling and waxing the screw threads, those miniscule brass screws broke off almost every freakin' time. (Leaving, of course, a brass pin sticking up exactly where you wanted a screw to go.) Finally ended up getting some replacement screws I had lying around to work, but I was very disappointed with the mess I'd made. Son didn't care - he's just happy to have a box for his rocks! - but the perfectionist Dad wasn't real happy. I've checked Rockler's website, and noticed that several reviewers mention the same problem with some of their small box hinges. So the question is, anyone have a source of hinges that come with GOOD screws??? I'll probably order a handful just to keep for the next "I need a box" occasion.

Thanks,

John

Re: small hinge source

#2

Brass screws

Lee Schierer - McKean, PA

>Brass screws are notorious for breaking off. You have to get the pilot holes just the right size and screw them in by hand with a small screw driver or the screw will break. I usually try to find a steel screw of the same size and use that to form the threads so the brass ones will go in without breaking. The pilot holes for brass screws need to be the same size as the root of the threadnear where the threads end and the shank starts. Make sure teh pilot holes are deep enough to accept the full screw length.

Beeswax works better than parafin (candle wax) for lubricating screws.

Lee

Re: small hinge source

#3

Why, LV, of course !

steve mackay

>

Re: small hinge source

#4

Re: small hinge source

Marvin Horn

>Best (only) reliable source for small screws I've located is Meisels. Screws are brass plated so not quite so fragile.

http://www.meiselwoodhobby.com/Products/ViewCategory.aspx?ID=69

Re: small hinge source

#5

I can relate...

Dan Mitchell

>I recently made a small box out of poplar & padauk as a 70th birthday present for my MIL. After examining a number of the less expensive hinges from Rockler, where one hinges is so loose it rattles & you need a crowbar to open the other, I finally ended up putting a $40 pair of Brusso hinges on the box. They look great, and my wife's mother is thrilled with the gift, but FORTY BUCKS???

I will say this, the Brusso screws did not break...

Dan

Re: small hinge source

#6

you need a set of number drills

Bill Tindall, E.TN

>I never understood how woodworkers got by with out a set of number drills and a caliper. They prevent this problem.

Step 1. buy set of number drills

Step 2. Determine the body diameter of the screw about half way up the shank. The body diameter is the diameter that does not include the threads.

Step3. On a scrap of the same wood drill a pilot hole bigger than you think you need based on the measurement in step 2.

Step 4 Install a screw in the scrap and see how it goes. Adjust pilot hole diameter and depth accordingly till screw goes in smoothly.

Step 5 Using what you learned install screws on the finish piece.

Whitechapel has the best brass screws. The aris on the LV screws is not sharp enough to suite my needs.

Re: small hinge source

#7

Re: small hinge source

Jim Dillon

>John,

I follow the suggestions by Lee and Bill and have had luck with small brass screws. Bill's recommendation for numbered drills is a good one. Several years ago I bought a set (Reid Tool, IIRC) and the very small sizes have sure come in handy for tiny screws, and especially for escutcheon nails. I also always test the size of the pilot hole by hand screwing (no power drill for sure) the screw into identical wood to judge the best size for the pilot hole. Maybe you got a bad batch of screws, although brass screws are known to be fragile. Hey, I'm sure your #2 son appreciates the effort. Well, maybe 8-).

Regarding a source of small screws, I've also had luck with Lee Valley.

Jim

Re: small hinge source

#8

Re: small hinge source *LINK*

Yonak

>This is off the current subject of brass screws, but not off the title subject : I recently bought some small brass hinges from a place called Craft, Inc. I believe their prices are quite good (although I have not extensively researched). They came highly recommended and they gave me have no reason to doubt the recommendation. The hinges I bought must be bought in quantities of at least 10, but that was no problem for my usage.


hinges

Re: small hinge source

#9

www.toolsforworkingwood.com

Dan Donaldson

>They have good brass hinges etc.

Re: small hinge source

#10

Re: www.toolsforworkingwood.com

Yonak

>For comparison, I checked out some 3/4" X 13/16" brass hinges at toolsforworkingwood.com. They sell for $17.05 per pair, if you buy 4 pairs or more. 3/4" X 7/8" brass hinges at Craft, Inc. sell for 14� each. To be fair, the Craft, Inc. hinges must be bought in minimum quantities of 10, don't come with screws and, especially important, are .03" in leaf thickness while the hinges at toolsforworkingwood.com are .09" thick, so it's all in what you are looking for. I don't work for Craft, Inc., but I have been recently impressed by them.

Re: small hinge source

#11

correction . . .

Yonak

>The Craft, Inc. hinges are brass-plated steel, I just found out.

Re: small hinge source

#12

Plus

Dan Donaldson

>The good hinges at toolsforworkingwood are brusso or equivalent. No comparison at all to 25 cent hinges.