Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

Shop Heater for Husband

Posts

Shop Heater for Husband

#1

Shop Heater for Husband

Mrs. Claus

>Santa would like to bring my husband a heater for his shop and would like some recommendations.

We live in a Southern region of the country where the lows very rarely make it below the 20s.

Santa would also like some recommendations about how much this should cost, because I just don't have the idea of what is reasonable for our needs. Santa (like everyone else this year) is on a budget and we move every few years, so I'm not looking to make a top of the line purchase.

Santa is looking for something that will keep his hand from turning to ice & allow his finishs to cure properly w/o being brought into my kitchen.

He has a free standing un-insulated work shop. I'm not concerned about the required electricity - every time we move he has to re-wire part of his work shop for something. It's about the size of double car garage w/ a pitched roof.

Thanks,

Re: Shop Heater for Husband

#2

Re: Shop Heater for Husband

Mrs. Claus

>BTW, Just read down further about the propane, etc heaters and thought I should clarify.

Santa is looking for an electric heater - not a propane, karosene or wood stove.

Again, Thanks.

Re: Shop Heater for Husband

#3

Re: Shop Heater for Husband

Dave Bair, Eaton Rapids, MI

>I have a ceiling-mounted quartz electric radiant heater that keeps my 20X20 Michigan shop warm all winter. It has two settings; I leave it set on the lower overnight and turn it about an hour before I start work. I bought the unit from Lee Valley a few years back, but they no longer offer them.

The unit was made by Marvin out of, I believe, Indiana. I don't know if they are still in business. But overhead quartz heaters are probably available from a number of souces.

Re: Shop Heater for Husband

#4

Re: Shop Heater for Husband

DizD

>I'm in southeast and I installed a celing mount electric heater. It has been more than adequate, just set it and forget it, but my shop is well insulated also. I believe mine is a Marley, but Dayton and others make comparable units. I found mine at Northern Tool.

Re: Shop Heater for Husband

#5

Re: Shop Heater for Husband

Fred Davis

>Mrs. Claus,

Tell hubby to rethinks his heater choice if he is doing finishing.

Electric heaters are fine if you don't need a quick warmup and if you don't care that they don't heat the air directly like say , a gas fired space heater.

Gas fire space heaters come in all shapes and sizes, for years I used one for heating houses I worked in and it put out 150,00 BTU which is probalay overkill for your needs, but look into the ones that mount right on a bottle of Propane , very fast warm up and cheap to operate compared to electric heat and you can take it with you when you move.

FredD

Re: Shop Heater for Husband

#6

Re: Shop Heater for Husband

Randy Johnson Connersville IN

>I'm not sure any heater is going to do a very good job if there is no insulation.

When I was renovating the building I use there was a period of really cold weather. I used a heater like the one Fred mentioned and it didn't do a very good job. Normally, as he said, it would have been overkill, but at that point in the project the ceiling had yet to be installed and all the heat went straight up and (literally)through the roof. I'm talking a 150,000 btu forced air propane heater in a roughly 30X30 former two gar garage.

Now, with the ceiling installed and a very well insulated attic, I keep it warm with a 35,000 btu propane ceilng heater. A stand alone kerosene heater was used before I got the unit I use now installed and (after insulation)it could just about run me out of the shop it got so warm.

The bottom line, is that without at least some insulation, operating costs each month might become prohibitive regardless of what kind of heater you have.

Re: Shop Heater for Husband

#7

Re: Shop Heater for Husband

Howard Norman

>I have an infrared electrical heater installed in my basement shop to heat the area around the wood lathe. It does a good job. It is installed on the ceiling and is adjustable. I don't know where one would get one since the company that made mine is out of business. I have a couple of the type that you get at Home Depot and they work, just not as well as the ceiling mounted one.

Re: Shop Heater for Husband

#8

Re: Shop Heater for Husband

GalenV

>Agree with Randy on the insulation. For sure if you mean it is also an open pitched roof put in a ceiling to reduce the volumn and what heat you have from going out the roof.

If you want to cool it in the summer as well you gain on both fronts with insulation first.

Re: Shop Heater for Husband

#9

A blonde Elf wired for 220V ?

Art Silva

>

Re: Shop Heater for Husband

#10

Re: Shop Heater for Husband

Tony - Memphis

>I live in the South too. My shop is insulated though (16x20). I use a combo AC/Heat unit from GE. It was about $350/$400. Keeps the place nice and cool or nice and toasty for not much money. Mine is in a hole in the wall (not a window). Works great. My experience in my old shop (two car garage with no insulation) was that no small space heater would work. I tried several.

Tony

Re: Shop Heater for Husband

#11

Re: Shop Heater for Husband

Bill White

>I too am in the South (Mississippi), and my shop is well insulated and attached to the home. Not a fair comparison, but I bought the oil-filled radiators 2 yrs. ago. I have two. Keep 1 on the floor and turned to low. Really cold? The second one comes out. No probs at all.

Bill