Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

OT: Computer screen problems

Posts

OT: Computer screen problems

#1

OT: Computer screen problems

Pat Evans

>My laptop screen has a horizontal gray bar near the bottom and two vertical black bars near the right side. The entire desktop shows above the gray bar and starts to repeat below the bar. The last little bit of the right hand side of the desktop is obscured by the first black bar and a portion of the right hand side of the desktop repeats to the right of the bar. I tried to do a screen print so I could post a picture of the effect, but a screen print shows the desktop as it should be. This used to be caused by the position of the screen, in that I could bring the screen to almost closed and reboot, and that would cure the problem. Now I can't make it go away no matter what I do. Any suggestions?

Re: OT: Computer screen problems

#2

Re: OT: Computer screen problems

Charlie Self

>I run slightly more costly monitors now, so there are lots of controls for positioning on-screen, contrast, brightness and on.

Even my older less costly monitors used to have controls that allowed positioning adjustments that got rid of the effect you're describing. If it isn't that, it takes more expertise than I've got to figure it, but if I remember correctly, CRT monitors tend to shrink picture size as they age and wear out. How old is the monitor?

Re: OT: Computer screen problems

#3

Re: OT: Computer screen problems

John K Jordan

>Part of what you are describing sounds like a digital problem, where some lines work and others don't. It could be due to either a connection problem (perhaps fixable) or a circuit failure (unfixable). Do you have controls like a stand-alone monitor for bumping the position of the picture on the screen? If so and you move the picture and the dead spots stay still, it's probably a hardware problem. A screen dump wouldn't catch that. That you describe a repeating section AND the previous reboot fix makes me wonder if your display driver has gone funky - might try updating or reinstalling the driver. A screen dump might not catch a software problem, depending on where it is.

What happens to the screen when you change the display resolution? Is it SET to the correct parameters?

Don't know about laptop screens, but I've fixed contact problems on screens on calculators and PDAs by disassembling and cleaning contacts. (BTW, I've been unsuccessful in fixing some as well.)

Some screens are connected to logic by strips of conductive rubber which can develop poor conductivity. I don't know about laptop screens, but even if connected by a multi-pin connector it might help to unplug and replug to reseat the connectors. This fixed one of my LCD stand-alone monitors.

Note that laptops (and other such electronic things!) are often very difficult to get apart since they are usually assembled with hidden snap locks. Be prepared to mutilate the plastic. Also, internal components are fragile.

But look on the bright side - new laptop computers have gotten so cheap they are almost giving them away in cereal boxes. :)

JKJ

Re: OT: Computer screen problems

#4

Re: OT: Computer screen problems

Pat Evans

>Thanks John. In response to your questions:

"Do you have controls like a stand-alone monitor for bumping the position of the picture on the screen?" No

"What happens to the screen when you change the display resolution? Is it SET to the correct parameters?" The problem remains when I change resolution. Also, yes it is set to the correct parameters. I'm running Windows 2000 and it tells me if I choose a non optimal resolution.

"I don't know about laptop screens, but even if connected by a multi-pin connector it might help to unplug and replug to reseat the connectors. This fixed one of my LCD stand-alone monitors.

Note that laptops (and other such electronic things!) are often very difficult to get apart since they are usually assembled with hidden snap locks. Be prepared to mutilate the plastic. Also, internal components are fragile." The screen is connected via ribbon cable and multi-pin connector. I had to replace a broken hinge, subsequent to the display problem, and was hoping the disconnection/reconnection might help. It didn't. That the position of the screen (ie whether it was fully or partially open) affected the problem made me believe it was mechanical, such as a broken wire or loose connection. That may in fact be the case, and disassembling it made it worse. You're right about hidden snap locks, but I managed to get it apart and back together without destroying it.

"But look on the bright side - new laptop computers have gotten so cheap they are almost giving them away in cereal boxes. :)" I'm retired and living on my investments. With the stock market and my IRA in the shape they're in, the only way I'll get a new computer is if someone is giving it away.

Thanks for your help. Hope someone has other suggestions.

Re: OT: Computer screen problems

#5

Re: OT: Computer screen problems

John K Jordan

>>"What happens to the screen when you change the display resolution? Is it SET to the correct parameters?" The problem remains when I change resolution. Also, yes it is set to the correct parameters. I'm running Windows 2000 and it tells me if I choose a non optimal resolution.

Well, when you change the resolution does the problem remain in identical size and position on the physical screen, or does it change in size with a lower resolution? I would expect the former of a hardware problem.

The thing that makes me wonder whether it's more than a broken or loose connection is the repeated screen image on the edge. That seems more like a hardware logic or software issue. I've seen a bunch of odd screen problems over the years but never one like that. We had one once that would work OK if you grabbed the frame and twisted the screen slightly. Ack.

I had a bad ribbon cable once on a $16000 video deck. You'd think they'd use better components in equipment like that. The stinking thing broke a tiny wire inside the cable and stopped the deck dead. $200 for a new cable since I couldn't flex it just wrong enough to find and fix it.

Hey, another option for your laptop might be to plug in an external monitor (assuming your laptop supports that) and keep using it as a desktop. You can find used CRT monitors for free - I've taken a bunch to the recycler.

Retirement - I highly recommend it. I retired a couple of years ago and while I had the best job on the planet, it's hard to imagine the structured work life again.

JKJ