Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

HELP- Planer Issue

Posts

HELP- Planer Issue

#1

HELP- Planer Issue

Dan Collins

>Friends: I have a DeWalt DW734 12" Planer. I've been noticing that my boards are not of uniform thickness. They gradually taper so that one edge is thinner than the other. I thought maybe the knives were off, but they are fine. Then I thought the bed was off, but it is flat. Tonight I looked closer and did some testing and found that the whole carriage that goes up and down (holds all the knives, motor, etc.) is slanted to one side so that the right side is lower than the left side. The instruction manual says nothing about adjusting the whole carriage. Can anyone give me some advice as to how to adjust it? I know what the customer service will say ... "Take it to our repair center", which is 50 miles away. I'm in the middle of a Christmas project and don't want to be without the planer for weeks. Any thoughts will be appreciated. Dan

Re: HELP- Planer Issue

#2

Re: HELP- Planer Issue

Larry Marker

>Go to www.dewaltservicenet.com and create a free account. They have short videos that you can download for how to fix just about everything. I haven't checked to verify that they have a video for that problem for the 734, but I have downloaded one for the 733 that I have and I suspect it's pretty much the same. If you can't find it, send me an email and I'll email you the video I have.

Larry

Re: HELP- Planer Issue

#3

Re: HELP- Planer Issue

George@Colonel's Workshop-Havertown PA

>Good Evening Dan,

I have the DW733. I experienced that problem one time, and discovered that the blades were improperly set. Before the discovery and the fix, I had to reverse the direction of the boards thru the planer to even up one side with the other's thickness. In a pinch around Christmas, there was no other viable alternative. In my case, the differential was very slight, and I was able to cope with the problem successfully until #3 son corrected the knife settings. Try swapping ends and running the boards thru again. Of course, the width of the boards you are working with makes a big difference. Mine were less than six inches, and the thickness differential was pretty slight.

Anyway, its worth a shot.

George

Re: HELP- Planer Issue

#4

Re: HELP- Planer Issue

Dan Collins

>thanks guys. I checked the dewalt site (should have done that before I posted the question). They do have a diagram on how to sdjust it. Hopefully it will work. Dan

Re: HELP- Planer Issue

#5

Re: HELP- Planer Issue

Jim Dillon

>Dan,

Recently, although my 733 does not have your problem (at least in a significant way), I've been doing exactly what George suggested. I usually do this after my last finishing cut to avoid any possible tearout from going in the opposite direction. Could be just my imagination, but I think it works - at least according to the calipers. Hope you get your problem solved. Keep us posted as to how you actually make that adjustment.

Jim

Re: HELP- Planer Issue

#6

Chet Kloss

Can you post a link?

Chet Kloss

>I am a member of the DeWalt site you listed but can;t seem to find any service videos.

Thanks,

,,,,,,,,,,,,,,,,,,Chet

Re: HELP- Planer Issue

#7

Re: HELP- Planer Issue- Success

Dan Collins

>Friends: Dewalt had a diagram on their website (it came up when I submitted a question via email to their customer service people). It turns out that it is very easy to adjust the carriage. You have to flip the whole planer up so you have access to the bottom, then you unscrew two screws and adjust the crank. It worked good and I'm back in business. As an aside, I think this problem was coming on slowly because the two screws probably vibrated loose, at least that is my guess. I had been flipping the boards for awhile to compensate for the narrower side, but when I actually measured the boards being flipped and planed recently, the center of the board was thicker than the two sides by about a 1/16th of an inch. Therefore, if you need to keep flipping the boards to make them uniform in thickness, you will probably start to notice that the center is thicker than the two sides. Fixing the carriage is probably a better idea. Thanks. Dan