Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Small router needed

Posts

Small router needed

#1

Small router needed

Joe Pack

>I'm in the market for a small router, primarily to be used to put a 1/8" radius on edges of hardwood toys. Any suggestions as to best values, best features, etc.?

Re: Small router needed

#2

Bosch Trim router, in my opinion

Craig in Silverdale

>

Re: Small router needed

#3

Re: Small router needed

George@Colonel's Workshop-Havertown PA

>Good Evening Joe,

I am almost embarrassed to post an honest and true answer. I was looking closely at the Colt and the Ridgid on Saturday at HD. They each look pretty, and pretty nice. I've been using a small HF laminate trimmer for the past five years or so, and find it more than adequate for that kind of duty. I bought mine for around $12.00. I also use it to gain hinges on cabinet work. I like the clear base. I see the price has soared to around $18.00 now. :<)

FWIW, I acquired an extra P+C stick on lable a couple years ago and slapped it on the barrel of the Harbor Freight machine, increasing my own prestige and imnproving the trimmers' performance. :<)

George

Re: Small router needed

#4

Self esteem doesn't come cheap

Clint Searl, at the base of Haycock Mtn

>

Re: Small router needed

#5

Re: Small router needed and table too?

GalenV

>When I went through the toy making phase I made my own router table from a formica sink cutout for a smooth surface for small part and also sized the hole for router bit just to clear the roundover bit.

The purchased ribbed table I had the parts would tip and hole was way to big for small parts. Probably could have put a piece of masonite over that table I guess.

I liked moving the small part not the router but then they had no small router except the Dremmel as a router.

MY kids WELL beyond wood toys and I guess so are grandkids! Yikes!

Re: Small router needed

#6

Re: Small router needed

Paul Waddle

>Way to go George!

Re: Small router needed

#7

Re: Small router needed

Tony - Memphis

>I have the Bosch Colt and have been real happy with it. It would be plenty to do 1/8" radii and such. My only issue with it is that the height adjustement can be a little tricky and there is a big gaping hole near the bit where I have to think really hard to keep my fingers out of! My tendency is to grip the top with one hand and apply pressure to steer it with the other. Its the other that gets near the opening.

Tony

Re: Small router needed

#8

Re: Small router needed

Karen

>>>FWIW, I acquired an extra P+C stick on lable a couple years ago and slapped it on the barrel of the Harbor Freight machine, increasing my own prestige and imnproving the trimmers' performance. :<)<<

LOL!

Re: Small router needed

#9

The P-C Police are comin' for ya George!

Art Silva

>

Re: Small router needed

#10

Check your email

Mark Goodall - ATL - tooljunkie

>

Re: Small router needed

#11

Re: Small router needed

Scott Greaves in Blackfoot Idaho

>I asked the same question here a few months back, and decided on the highly recommended Bosch Colt. What a nice little router! It did everything I wanted it to do, and I believe it is capable of much more! Now it is my favorite router (out of four), and I will reach for it first, and only switch to one of the others when I have to. I can't say enough nice things about this great little router! BTW, thanks to all those who recommended it to me!

Scott.

Re: Small router needed

#12

Porter Cable 310... a dying breed

Scott in Montana

>I too have a Bosch Colt and like it quite well, but overall I perfer the low center of gravity on my Porter Cable 310 router. I also like the quantity of metal used in its construction and a number of the aftermarket attachments you can get for it. I know it's discontinued but there are still lots of them available. I think I bought the a couple from Tool King for about $150 each.

Happy Holidays,

Scott in Montana

Re: Small router needed

#13

Re: Porter Cable 310... a dying breed

Glenn Madsen

>I'm really happy with mine, leaving it set up for certain cuts.

Overall, a much better tool than the little Bosch I also own. More money, though.