Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

How thin to joint safely?

Posts

How thin to joint safely?

#1

How thin to joint safely?

Clementine

>I have some very old 3/4" cedar boards that I'm going to line a blanket chest with. By the time I get them cleaned up, they will be about 5/8". I want to have them about one-quarter inch for this. Even if I resaw them (which I've never done), can I safely use the jointer to get them to one-quarter inch? I'm open to a better idea.

Re: How thin to joint safely?

#2

Re: How thin to joint safely?

David Yoho

>Clementine, the answer to your question is - no.

In the absence of hand planes and the ability to use them, you'll need a jointer to flatten one face of your stock. However, you will not be successfully in achieving a uniform thickness with just the jointer. Once you get one face flat and true, you'll need a planer to finish the job. The two-speed "lunch box" planers out there do a great job and can take your stock down to 1/4-inch thickness with no problem.

If you don't have a planer, I think it's the next investment you should think about. Being able to dimension your own stock opens up many new possibilities in woodworking, not to mention the savings of buying rough stock and dressing it yourself to your specific needs.

If you would like to hear owners opinions as to which one they would recommend, start a new message with an appropriate topic heading and see what folks here say.

David

Re: How thin to joint safely?

#3

JL

Planer?

JL

>I'd be uncomfortable using a jointer to thin down pieces that thin. I'd prefer to use a planer myself. I typically use my jointer to joint larger pieces. If I were to use a jointer, I'd want something like Grippers to keep my hands well away from the jointer blades.

Re: How thin to joint safely?

#4

Re: How thin to joint safely?

Joseph Mulherin, Sr

>Another idea is to run them thru your bandsaw verticallly to halve the boards, then run them on the jointer....with safety gloves and a push stick...keep your fingers out of the way of any blades... and use a 1/2" or 5/8" 3TPI blade.

Re: How thin to joint safely?

#5

Re: How thin to joint safely?

Carol - now back in Dubuque, IA

>DO not use the jointer - unless you have more fingers on your hands than you need.

Seriously, the jointer is not the right tool for this. A planer is.

The jointer will not make the pieces the same thickness.

Find a woodworking friend and borrow one. That is one good reason to belong to a woodworking club. And tell us where you are. Maybe one of us is nearby and can help you out. I would in a nano second!

Re: How thin to joint safely?

#6

Re: How thin to joint safely?

Dave Paine

>I have to agree with the other replies, a jointer for 1/4 inch is not recommended.

A planer works well, although may result in some snip depending on the model.

My personal preference for this task is drum sander, since I have one. This is very safe and has the benefit of not tearing out the grain. Not likely an issue with the cherry unless you have some wild grain on a piece. I have cleaned up 1/16in to 1/8 in thick boards for a friend to use for shaker box sides with my drum sander.

As another reply stated, try and find a friend or even post on the "Wanted" board. I expect many people would be happy to spend the few minutes it would take to clean up the boards.

I live in Eastern PA about 90 miles north of Philadelphia if I happen to be close enough for you to drive.

Re: How thin to joint safely?

#7

Re: How thin to joint safely?

George@Colonel's Workshop-Havertown PA

>Good Afternoon Clementine,

If the cedar boards are fairly flat, you may be able to split them on your bandsaw into two resawn halfs, and run each side of each half through your planer. You will maximize yield.

George

Re: How thin to joint safely?

#8

Dale Lenz

Re: How thin to joint safely?

Dale Lenz

>How wide are your cedar boards?

Re: How thin to joint safely?

#9

Re: It can be done safely

Dave Anderson (PacNW)

>First you want to face joint your boards. Second resaw them by what ever method Bandsaw, tablesaw or handsaw. Third, Double stick tape the resawn boards (smooth face) to a board at least as wide as the others. Forth, take very very light cuts untill you get as thin as you need. This method prevents chattering. It will work, if you can't find a planer ( preferd method0

Re: How thin to joint safely?

#10

Re: How thin to joint safely?

Joseph Mulherin, Sr

>I stand corrected....use a planer...borrow one or have someone do the work for you. I agree...do NOT use a joiner to do this type of work?!!!! My BIL put his hand into a dado blade yrs ago and he paid with some ugly fingers.....

Re: How thin to joint safely?

#11

Re: It can be done safely

Carol - now back in Dubuque, IA

>Dave, I'm going to caution against this as well. We do not know the expertise of the original poster.

However, a good friend of mine with lots of experience recently lost three fingers in a jointer operation that would have more appropriately been accomplished another way. He (and I) thought kick back on a jointer was a relative non-issue. Not true!

It is too easy for a board to become unstuck from whatever hold-down method being employed, leaving the wood to launch via a kickback, and leaving one's hands being fed into the jointer knives. This is one tool where using two push blocks to move the stock across the cutters is a really smart idea.

And the jointer never promises parallel faces, which I assume to be another objective with this thinner stock.

Sorry to be so ugly about this, but this is exactly what is at stake here.

Thanks for bearing with me. It is the old woodworking teacher rising to the surface. My class motto was, "no blood on my watch!" And I was pretty much a bear about it. No apologies.

Re: How thin to joint safely?

#12

Re: How thin to joint safely?

Bill Houghton, moderately nice in Sebastopol, CA

>If you're lining your cedar chest with them, then one side won't be visible. After you've resawn them, if you can (bandsaw up to your saw's capacity, or tablesaw if they're up to about five-six inches wide; I won't go into resawing technique here), you could acquire a hand plane to smooth the visible side. It's not hard work, and smells great.

Re: How thin to joint safely?

#13

Re: It can be done safely

Dave Anderson (PacNW)

>After reading your post, I agree that the expertise of the origanl poster is not known. I used this technique for along time. There are varibles that I did not take into account, the quality of the tape for one. This should only be attempted by experiensed (sp) personal. Since I got my first lunch box planer 20 years ago, I have not used this method. I highly reccomend using a planer to make any stock less than 1/2"

I stand properly chastised

Dave Anderson (PacNW)

Re: How thin to joint safely?

#14

Re: How thin to joint safely?

Clementine

>Great advice - and for someone very little above a rookie. I do have a Delta planer, but I just hadn't thought about using it, especially the way described here. I guess I'll have to learn to resaw! From what I read here, I will resaw with a 3tpi 1/2" blade and then plane to 1/4". Thanks, everyone.

Re: How thin to joint safely?

#15

Re: It can be done safely

Carol - now back in Dubuque, IA

>Please don't feel chastised, Dave. Your response came from your level of expertise and from the equipment you are used to using.

It's just that sometimes we responders overlook parts of the bigger picture of the original poster.

I posted because I know machines used the way they are intended can indeed be dangerous to use. When used in marginal ways, they are destined to be instrumental in the event of accidents.

We know that. We just sometimes take it for granted that others know that as well.

Re: How thin to joint safely?

#16

Re: How thin to joint safely?

Carol - now back in Dubuque, IA

>Hooray! Glad you have a planer.

Play safe. And come back for advise. As you can tell, we love to help.

Re: How thin to joint safely?

#17

Re: How thin to joint safely?

Jim Dillon

>Clementine,

Agree with all the great advice you got. Glad to hear you have a planer, it can be a great asset to your woodworking. When planing thin stuff, I have found having a wooden/MDF shelf on top of the planer metal "wings" helpful. It relieves your mind about the spinning planer blades when they get close to the metal surface, and I think it helps minimize snipe. Here is a pic to better show what I am talking about.

Jim


img

Re: How thin to joint safely?

#18

Yup, And..

George@Colonel's Workshop-Havertown PA

>Agree Jim,

I always use an auxiliary table with mine. I find my DW733 hard to crank down much below 1/2 inch, so I use the aux table as a 3/4" spacer, thereby achieving sanding nirvana and workshop spiritual bliss.

George

Re: How thin to joint safely?

#19

Re: Yup, And..

Jim Dillon

>Hi George,

Glad to hear the auxiliary table works for you as well. Funny, I had noticed the same thing about getting more difficult to crank when below 1/2 inch - even when the planer was new. Not a deal breaker though, and as you said, the table minimizes that problem. In fact, the table works so well, I keep it on full time. The 733 has been an amazing work horse and I would buy the newer model in a heartbeat if the 733 blew up.

Jim

Re: How thin to joint safely?

#20

Blew Up.

George@Colonel's Workshop-Havertown PA

>HI Jim,

Mine goes to De Walt about once every 18 months. Its a good tool, but needs work more often than any other tool I have in the shop. Of course, I USE it pretty much, and that may account for the repair schedule. My #3 son also has an identical machine, but isn't nearly as active in its use. I do like the way mine performs, but not necessarily on cut nails. My blades vacation in the Phoenix area frequently at the Scott Whiting spa.

George