Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Garage cabinet doors

Posts

Garage cabinet doors

#1

Garage cabinet doors

Brad in MD

>I'm getting ready to build some storage cabinets for the garage and thought I would do a frameless design. Cabinets would 80 high, 24 wide, 18 deep and 36 high, 24 wide and 18 deep made from 3/4 plywood. My question is on the door design. I'm thinking about using mdf that I would paint (quick, easy and inexpensive) in a full overlay fashion: would using a Blum frameless hinge and its screws hold in 3/4 mdf? Any other suggestions.

Thanks,

Re: Garage cabinet doors

#2

Re: Garage cabinet doors

Carol - now back in Dubuque, IA

>3/4" MDF is darned heavy! Doors hang on one edge, if you think about it, and they take a certain amount of abuse. And muscling around MDF is no joy.

That said, I'd look at a lighter material.

FWIW, I looked at making my own doors for a kitchen project and found that companies that specialize in door and drawers were selling them for less that I could buy the material. That was a no brainer. However those were also cherry doors. And the quality was quite high. :-)

So, I'd pencil out different materials (plywood, Melamine, MDF, particle board, etc.) and then head off to the borg and see what I could get in the way of ready made doors.

Finish and hardware are out of the equation here. You need those anyway.

When you subtract your penciled cost and the borg's cost, at least you'd have what your labor is worth.

Since these are garage cabinets, and since you may want to have the experience of making doors, it may be worth it. Or not. But that is your decision. Just trying to help you make an informed one. :-))

One other thing. If this project involves new tooling, then you get to factor that in as well.

Unless the new tooling is classified as the just rewards of s serious toolaholic!

See how complicated these things can get?!? LOL!

Re: Garage cabinet doors

#3

Re: Garage cabinet doors

Clint Searl, at the base of Haycock Mtn

>That's exactly what I did on our master bath vanity cabinet about ten years ago. It gets lots of exercise with no problem whatsoever. The hinge inset is so tight that there's no chance of wiggle deterioration. Mine took a 35mm forstner hole. Did it on another two bathroom remodel, too.

Clint

Re: Garage cabinet doors

#4

Re: Garage cabinet doors

Thomas S Stockton

>Blum has a chart on how many hinges you need. It is probably on their website, it takes into account both height and width. I'm gueesing your going to need 4 or 5 hinges for a door that size.

Tom

Re: Garage cabinet doors

#5

Done that

Mark Goodall - ATL - tooljunkie

>"...Cabinets would 80 high, 24 wide, 18 deep and 36 high, 24 wide and 18 deep made from 3/4 plywood..."

I made cabinets for my workshop almost exactly that size. Basically 8' tall and 4' wide (size of a sheet of plywood) except I made it 7' tall it wouldn't hit the ceiling :)

So each door was 84" x 24" made from 3/4" birch plywood. Those were very nice. Strong and firm without being overly heavy. I would imaging MDF would feel considerably heavy. I'm not a fan of MDF anyways.

I used piano hinges as they spread out the weight more evenly (I assume).

They didn't fit well in my new garage when we moved here so I gave them to a neighbor down the street. They were pretty heavy to move... can't imagine if they were MDF. I still see them when I visit, and comment on what nice cabinets they have in their garage. :)

Happy Woodworking!

Re: Garage cabinet doors

#6

Re: Garage cabinet doors

mdclor

>I agree with Mark that MDF is darn heavy. However, if you were so inclined, you could make flat panel doors using poplar for the frame and thin MDF for the panels. That design might not suit you since you want frameless doors, but you could cut the weight of each door by half. Just a thought.

Merle

Re: Garage cabinet doors

#7

Re: Garage cabinet doors

Barry Irby

>I don't have much experience with frameless doors and cabinets, but was not impressed with the few I have dealt with. It seems to me that the MDF doors would be very heavy and that the side of the cabinet would be weak and warp or buckle, allowing the doors to sag when they are closed. This is assuming the sides of the cabinets are unreinforced MDF also. The piano hinges Mark mentioned might spread the load better, but screws don't hold well in MDF. I would be inclined to make flat panel doors to cut the weight down and to reinforce the cabinet with some sort of facing.

Re: Garage cabinet doors

#8

Re: Garage cabinet doors

George Koch

>Brad, I think an inexpensive 3/4' lumber core , such as lauan, would fit the bill for those doors. It is lightweight and also resists warping. George

Re: Garage cabinet doors

#9

Re: Garage cabinet doors

mdclor

>Sorry, I meant Carol.

Re: Garage cabinet doors

#10

Re: Garage cabinet doors

Tony - Memphis

>I did something similar for my garage. I made a door out of poplar rails and stiles and masonite for the panel. I glued the panel in and painted them. They look nice, they are light, and very strong. Ten year later, they are holding up quite well.

Tony