Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Making Picture Frames

Posts

Making Picture Frames

#1

Making Picture Frames

Hamish------WebKitFormBoundarye+AennU0BR2KFUwD

>I have been looking through the list of books Amazon has to offer on making your own picture frames out of wood and all I have found so far was a book written in 1958 by Manly Banister called "Making picture frames in wood". There are a bunch of others but they don't really seem to deal with the carpentry side of things. Like most of you all, I have various scraps of interesting pieces of wood hanging about that I feel could be turned into picture frames for some of my photographs but so far can't seem to find an adequate book that explains how to do it.

Any ideas?

Thanks, Hamish.

Re: Making Picture Frames

#2

Interesting Half Lap method *LINK*

Mark Goodall - ATL - tooljunkie

>Years ago I came up with a way to do make picture frames. I posted a spreadsheet that calculated all the dimensions. Wow, that was over 10 years ago. I probably should replace the Excel spreadsheet with a slicker online calculator. Well anyways, for what it's worth the link is below as well as an example diagram.

Let me know if you end up using it. I get a kick out of receiving emails from people all over the world who found the instructions and made some frames usign this method.

Happy Woodworking!


img

http://www.happywoodworking.com/PictureFrameHalfLa

Re: Making Picture Frames

#3

Prefer Miter Joinery

Greg

>Best to hide the end grain with precise miters. Fine Woodworking magazine has had a few articles on this. The key is precision milled pieces, exact 45 degree cuts and a method to reinforce the joint. There are several ways to do this with splines, either hidden or using a different shade of wood for effect.

With practice, you will be be making strong and good looking frames.

Re: Making Picture Frames

#4

Actually

Mark Goodall - ATL - tooljunkie

>"Best to hide the end grain with precise miters"

Hmmmm, can't say I completely agree. I've found that many people actually like the look of the lapped joints, with the constracting colors achieved by exposing the end-grain, rather than hiding it in a miter. I also like the contrasting look of a wedge tennon, or even a dowel used in joinery.

Happy Woodworking!

Re: Making Picture Frames

#5

Ellis Walentine

Picture frames

Ellis Walentine

>This is a topic that never goes away. Every woodworker makes picture frames -- at one time or another, in one way or another. My own philosophy of frames is that they exist to separate the object visually from the surrounding space. *How* you wish to do that is your aesthetic decision.

For my part, when I need to make frames, I usually miter the pieces, glue them up, and then tablesaw the corners using a simple jig that holds the frame at 45� to the table.

Splined miters are easiest if you can saw the kerfs in flat stock. Molded stock takes more setup time.

Ellis

Re: Making Picture Frames

#6

Re: Making Picture Frames

Paul Waddle

>Two important points: 1. opposite sides need to be same length,2.precision miters. The first is self evident,the miters are sometimes a booger. I have a saw jig that gets close,but not perfect-even if perfect,the cut depends on the sharpeness of saw blade.

My reccomendation is to buy a guillotine cutter ~ 145$ at Woodcraft. For clamps,buy the set that uses adjustable all thread and its pretty easy(and slow). You can fine tune the fit however. Or make a layout on a pc of ply wood,glue some cleats and use wedges to force the joints together. Either of these methods means you first have to cut the miters close,just use the guillontine to nibble the 45 joint. I glue up the frames and use table saw to cut a spline, and glue it in. After dry,trim and sand. Actually, a band saw cut is good,just sweeten it with the cutter. pw

Re: Making Picture Frames

#7

Re: Making Picture Frames

Fred Davis

>When I started making a lot of Wainscot and the step moulding for the panel inserts, I needed a fast accurate way to permanently fasten the mitered joints so I could attach the panels to the back of the frame.

What I came up with works every time if you can pay attention to how quickly the joint sets up using Gel Cryanolate glue and accelerator.

Only down side is not paying attention and not having a can of Acetone nearby and you glue your fingers together or to the frame.

You only need to do it once to get the hang of it and then your good to go.

If you do this , assemble the frame joints on top of wax paper to prevent bonding to your workbench.

I made a jig that slides in both slots on the table saw with a 2x2 laid out with a framing square to hold the stock exact for the mitre.

Also I use a stop for repeated cuts , sometimes nearly a hundred at a time for the length and width of the frame.

For this type of operation you do need accurate mitres and repeatability of the cuts and lengths.

FredD

Never had one come apart, I would say tho that apart form the frame being attached to the plywood panel, a spline could be in order for reinforcement when it is purely a stand alone picture frame.

Re: Making Picture Frames

#8

Re: Actually

George Koch

>Another option would be a half lap joint with a mitered face. George

Re: Making Picture Frames

#9

Just finished 2 using Mark's method...

John E in SC

>I've made 4 now out of eastern red cedar, and I think they're gorgeous. (Mark, I sent you an e-mail awhile back thanking you for the method. If you didn't get, well, thanks again!) They looked so good, I've had several folks ask me to make some more for them. I used a walnut plug in the corners for a little contrast. Very easy to make, and with the right wood, I think they look better than mitered corners.

John

Re: Making Picture Frames

#10

Re: Making Picture Frames

Clint Searl, at the base of Haycock Mtn

>As the others have pointed out, once you nail the miter, the rest is downhill. Profiles can be created on the TS using stock S4S material, and stock mouldings can be combined to make more elaborate profiles. Here's the wildest one I did using stuff from the Borg. It's 34" square and gold leafed.

Clint


img

Re: Making Picture Frames

#11

Re: Making Picture Frames

Hamish------WebKitFormBoundarye+AennU0BR2KFUwD

>Gentlemen, many thanks for your numerous responses and ideas and for sharing with us Clint, your gold leafed picture frame. That is sure to enhance any wall.

I recently posted a thread on making trim for windows in our house and without thinking about it at the time, see that has bears many similarities to picture framing. In both cases I would like to finish them off to show the richness of the natural wood tones.

Happy woodworking, Bernard.