Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

A bit OT: DC wiring help.

Posts

A bit OT: DC wiring help.

#1

A bit OT: DC wiring help.

Paul Woolson

>Sorry for the off topic post but I know there are a lot of electrical gurus here.

I've got an idea banging around in my head to slightly automate the raise/lower of my wide belt/ thickness sander. The crank is on the opposite side of the machine from where I stand to feed the stock. So my thought is this: rather than reach around and manually crank the turn wheel, what about installing a motor to do this job? I'm guessing I'd need a DC variable speed reversible motor. Thing is, I know nothing about how to do this. Can someone point me in the direction of a book or website that would show me how to wire a DC motor into this AC system and hook it up with reversible toggle and rheostat?

Also, something that would be cool would be some sort of a shut off switch which would kill the power of the motor when it made one revolution. Then I could just hit the toggle again to make another revolution. Is this possible? Thanks and sorry for my very elementary education on this topic.

Re: A bit OT: DC wiring help.

#2

Re: A bit OT: DC wiring help.

Pete LaBelle

>You will need some sort of limiting switch at both ends of the travel, else your electric motor will do damage to something. Will be more involved in the wiring aspect now. Understanding what type of voltage you decide to use will help determine the type of limit switches you will need.

1 revolution of the motor ? Most likely will have to deal with a gear box in the equation.

Pete

Re: A bit OT: DC wiring help.

#3

Re: A bit OT: DC wiring help.

Paul Woolson

>Thanks Pete,

Unfortunately, I'm such a noob that I really don't know what type of voltage I want. All I really know is that I'd like a motor that spins quite slowly (somewhere in the 50-150rpm range) that is variable speed and runs both directions.

A friend recommended a PLC (Programmable Logic Controller) but that's WAY over my head, technically.

Re: A bit OT: DC wiring help.

#4

Re: A bit OT: DC wiring help.

Fred Davis

>Why don't you forward your post to the comapny that made your sander and see what they say?

FredD

Re: A bit OT: DC wiring help.

#5

Re: A bit OT: DC wiring help.

Barry Irby

>Not sure, but I think this is way more complicated that it first appears. As pointed out, you would need upper and lower limit switches to prevent crashing into either end of the travel. Also, I have a Performax, not a wide belt sander, but I seldom turn the crank a full turn. More like a quarter turn or even less. Look up a Stepping Motor. Again, not sure, but I think there are motors designed to turn a given amount and shut off. Another problem woudl be that you woudl wnat some sort of over-ride so that you could change thickness dramatically when you wanted to, such as when you decide to sand something four inches thick after sanding something 1/4" thick.

Wonder if the motors for power car windows could be adapted?

Re: A bit OT: DC wiring help.

#6

Re: A bit OT: DC wiring help.

Paul Woolson

>Sorry for the confusion. The hand wheel is already geared so that one full turn moves the belt up or down .020".

Yes, maybe a stepper is a good place to look. I'll see what I can find out. Thanks, Paul

Re: A bit OT: DC wiring help.

#7

Re: A bit OT: DC wiring help.

GalenV

>First thing you need to do is find out how much torque it takes to turn the shaft. Maybe you can remove the handwheel and turn with an inch pound torque wrench. If relativly low torque you might use a light spring scale and connect to the rim of the handwheel and pull to get torque. May be in.-oz. and not ft.-lbs but you need to see. You need to size the gearmotor on torque and speed. You say this is already geared so you know amount of turns per fraction of an inch of travel. Sounds like you want to bump the drive about one turn of your shaft so need a lot of gearing to reduce say an 1150rpm or slower motor to 1 rpm output. (Assumes you may want to bunp for 15 second for 1/4 turn) If you cannot get a slow enough gearmotor you could connect by a chain drive or belt and get the final reduction to slow down.

First stepping motors are usually small low torque and you probably need a gearmotor. Some gearing will be self locking and not reverse but spur or helical will.

Even if you are thinking salvaged part like pulling the trigger and circuitry from a variable speed drill to put where you can rach it and using the motor and gearing, just bumping it would be too fast.

If really low torque you might find a mechanical cam timer motor as I have used them. They are in.-ounces of torque and can be down to RPH.

I like tinkering but it may not be worth your effort. The suggested travel limit switches are a good idea but assume you will be standing right there to stop if needed.

Anyway start by finding out what you need for torque to turn the shaft and then what possilbe drives.

Long story, sorry. Old mechanical engineer in me and nothing to tinker with today.

Galen

Re: A bit OT: DC wiring help.

#8

Actually

Dan Donaldson

>I don't think that the electrical issues are going to be the main problem. First, you need to figure out what kind of a mechanical setup you would need to do what you want. Torque, speed, reversibility, etc. Once you figure that out and get the mechanical parts, then you can do the electrical. You really can't do any kind of electrical design until you know more about what you need to control.

Perhaps another suggestion: Get a flexible shaft with a crank on the end, route it around the machine to connect to the adjustment shaft, and use that to make it possible to adjust from the front. Probably a lot less expensive and definitely a lot safer and more foolproof.

Re: A bit OT: DC wiring help.

#9

Re: A bit OT: DC wiring help. *LINK*

Carol - now back in Dubuque, IA

>Linear motors?

I used three of these a few years ago to automate an ambo (pulpit) for handicapped students. Slow, powerful. I added limit switches where necessary. The motor itself has internal limit switches so it can't self-destruct. But the wiring was, well, shall we say, interesting. Basically it is primitive, manual, Boolean logic control. One switch opens, another closes, providing a reversing path. Time six. Either end of three motors.

But I did not wire it to move a quantified amount. That would be even more interesting.


Linear Motors

Re: A bit OT: DC wiring help.

#10

Re: A bit OT: DC wiring help.

GalenV

>Linear motor would seem to yield the wrong motion but could be used to drive a rack with a pinion to replace the handwheel on the shaft.

Slow linear movement of the rack would rotate the pinion.

Good idea as they can provide good force and based on pinion size good torque.

Re: A bit OT: DC wiring help.

#11

Re: A bit OT: DC wiring help. *LINK*

GalenV

>Dans mechanical means really sounds the best and gets away from the electrical.

But to answer your real question the link has about the most simple logic I can find right now. The power supply could be an AC to DC power supply but it's size is drive size specific. The rheostat is not shown but it would be wired between the positive side of supply and the connection to the switch. The positive is connected to one side of the resistance and the wiper is connected on to the switch. If you want a fail safe the other side of the resistance is connected to the wiper. If the wiper breaks contact it reverts to full resistance. The toggle would be best to be momemtary on with spring return to center off. That way it only drives for the time YOU hold the switch in either direction. All components are still subject to load (Motor amps)

Hope this really answers what you ask.


http://www.distel.co.uk/DC_MOT_CON1.htm

Re: A bit OT: DC wiring help.

#12

DC MOtor is not necessary

Larry Marker

>There are reversible AC motors, too. Garage door openers, for example. Ceiling fans for another.

I doubt that variable speed is going to do you a lot of good. You will need to be geared down so far to get into the range of practicality that trying to speed up the drive much is not going to do much for you other than to grind up the gears.

I would go for a mechanical solution myself, but if you are bent on a motor, you can look for both AC and DC. There are lots of applications -- motorized window curtains, motorized awnings, motorized driveway gates, electric dumbwaiters, etc. -- that are potential sources of appropriately sized motors.

Larry

Re: A bit OT: DC wiring help.

#13

Re: A bit OT: DC wiring help.

Alan in Little Washington (NC)

>You don't need a DC motor unless you want to change the speed. I did that with the conveyor on my dual drum sander. I replaced the AC gear motor with a DC gear motor and (AC to variable DC) controller.

Larry is correct, for your application you just need a reversible AC gear motor. I added one to my router table to make it a powered lift. I just wired the motor to a spring loaded, center off, double throw toggle switch. I got my motor from the Surplus Center but it would likely not be strong enough for your application.


img

Re: A bit OT: DC wiring help.

#14

Sounds like a job for.....

Mark Goodall - ATL- tooljunkie

>MacGyver!

:)

Happy Woodworking!


img

Re: A bit OT: DC wiring help.

#15

Motorized router lift - Very cool!

Ray Carson - Lawrenceville, NJ

>Hey Alan,

That's about the coolest thing I've ever seen. Very ingenious. If you could patent that, you be a rich man. My only question is, how do keep the dust off the motor and setup you show in your picture?

I copied your picture to my "My Pictures" folder for future drooling. I love your idea. Awesome!

Ray

Re: A bit OT: DC wiring help.

#16

Re: Motorized router lift - Very cool!

Alan in Little Washington (NC)

>There is enough suction/flow from my DC to keep the motor clear.

Re: A bit OT: DC wiring help.

#17

Wasn't there Going To Be An Article???

George@Colonel's Workshop-Havertown PA

>Good Morning Allan,

Wasn't there to be a Wood Central article or Shop Shot of your creation? There ought to be.

George