Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Miter "clamps" using packing tape

Posts

Miter "clamps" using packing tape

#1

Dale Lenz

Miter "clamps" using packing tape

Dale Lenz

>Got 5, typical 4 sided box frames, to glue up. Just glued the first one up, came in for lunch, will finish other 4 after lunch. Seems to work okay. I could squeeze the box frame opposite the miters corners and could get a little more glue squeeze out of glue. Using 1.5" tape on 3" wide wooden frame. Any words of wisdom?

TIA

Re: Miter "clamps" using packing tape

#2

Re: Miter "clamps" using packing tape

John McGaw

>You don't want too much squeeze-out otherwise you will just be weakening the joints. I've used a similar method with blue masking tape as the first step. After the structure (hex or octagon tubes in my case) were glued up and pulled together I wrapped the tubes with either latex surgical tubing or banding. The latter was a left-over from two carpal tunnel surgeries where it is used as a step in the anesthesia process. Instead of having them throw it away afterward I took it with me -- handy stuff and my insurance was probably billed $1K for each.

Re: Miter "clamps" using packing tape

#3

Re: Miter "clamps" using packing tape

Fred Davis

>Dale ,

I haven't atually tried it yet , but I have been kicking around the idea for years about using a blood pressue cuff to clamp round stuff.

After feeling the pressure from having them used on me , I would say it would do the tirck.

FredD

Re: Miter "clamps" using packing tape

#4

Re: Miter "clamps" using packing tape

John E in SC

>Doubt that would work very well. BP cuffs don't apply pressure evenly. They have a bladder that inflates, and it doesn't go all the way around. If you like next time you get your BP checked, there is usually an arrow on the cuff used to locate over the brachial artery, which is where you want the pressure concentrated.

Nice thought thought though. I have seen (and used) a similar concept back when I was growing up. My Dad used to run a service station, and my teenage years were spent changing tires. We used to have what looked like a fire hose with a valve stem on it that you could fasten around the middle of a tire that wouldn't seal to a rim, and then when you inflated the hose, it would squeeze the tire to make the bead seal better with the rim. A similar concept (where the "bladder" goes all the way around could probably clamp round, or nearly round, objects fairly well.

Re: Miter "clamps" using packing tape

#5

Re: Miter "clamps" using packing tape

Paul Waddle

>If it works for you,then it works! I prefer a board on which cleats are glued around the frames, and wedges are snugged tighly between the frame and the cleats,pulling the frame together. I think for round frames,some of the other solutions suggested work better. pw

Re: Miter "clamps" using packing tape

#6

Dale Lenz

Re: Results

Dale Lenz

>Not bad, I've seen better but seen far worst. Will know more when I start sanding and can see the miter joint better. One thing for sure: taping the joints prior to gluing sure does make managing the box easier. Might add a strap clamp to the mix next time.

Re: Miter "clamps" using packing tape

#7

Re: Results

Barry Irby

>I have made a bunch of cylinders by gluing up staves and then turning them on the lathe. Hit upon using packing tape and large pipe clamps. Lay them out face down and run two strips of tape, turn them over, glue the joints, roll them up and apply the clamps. The tape even keeps any staining that might come from the clamps off the wood. For a box, I would suggest bungy cord, strips of rubber, surgical tubing, or s strap clamp or two.