Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

Bending padouk veneer

Posts

Bending padouk veneer

#1

Bending padouk veneer

Dan Mitchell

>I bought a piece of padouk to make a base for a pottery lamp my wife has made. Since most of the wood will not be seen (as it's under the lamp) I decided to try cutting some veneer strips to apply to MDF, rather than using all this beautiful wood & have it hidden. Below is a pic of the veneer I cut on the band saw & the MDF disk. The strips are ~3/64" thick, the disk is 9.25" in diameter & about 3/4" high. Applying the top part is pretty obvious, but I'm wondering the best way to apply the band around the circumference of the disk. It seems as though the wood will bend to a circle that size, but it takes a fair amount of force to get it to do so, & I wouldn't be surprised if it snapped at some point. Should I soak it in water 1st? I've read about steaming, but I don't know how I'd accomplish that. Also, if the wood is wet from soaking, how does this affect the gluing process & the MDF? What's the best clamping method for this process? I'm thinking of either using a band clamp (I have one of those Bessey framing clamps), or a ratcheting cargo strap I have.

TIA

Dan


img

Re: Bending padouk veneer

#2

Re: Bending padouk veneer

Thomas Skaggs, Foothills of Mount Level

>Try dampening some paper towels in water and then wrapping your veneer strip in the paper towels for a while to make them more plyable. A strap clamp works well. A racheting tie-down might be overkill with the amout of hardware they have. Something like a Pony strap clamp would be great. Good luck!

Tom

Re: Bending padouk veneer

#3

Surgical tubing?

Scott in Montana

>I stretch surgical tubing around cylindrical forms or curves when wrapping veneers around them.

Scott

Re: Bending padouk veneer

#4

Re: Bending padouk veneer------WebKitFormBoundary+

Keith Newton------WebKitFormBoundaryV6MZb+tiOpocz6

>Dan, While it is tempting to make the wrapping veneer thicker. I would consider making it thinner. Each doubling of thickness means quadrupling of stiffness more or less.

I would avoid wetting as Thomas suggested. While wet wood is more limber, it only allows the cells to be more limber, and flex under the bending forces while wet, but doesn't allow the cells to actually slip by one another, to gain a new memory, which would leads to spring-back, and other gluing problems at the ends / joint.

For something this small, why don't you just saw the circle out of solid stock. Surely the material is cheaper than the cost of your labor.

------WebKitFormBoundary+VrWUBcwZauAlw80

Re: Bending padouk veneer

#5

Re: Bending padouk veneer------WebKitFormBoundary+

Paul Woolson

>I bend wood in this fashion all of the time (I'm a professional guitar builder). one of my common bends is a 4" radius soundhole binding.

I know padouk pretty well. It doesn't like to bend. From my experience, I would absolutely not add any water to the wood. As said before, that loosens the cells but not the fibers, so it will sort of tear rather than break. But it will do that very easily.

Here's my method that will work well for this process since it's an outside curve. Get some of that strapping tape. The plastic stuff with the fibers in it. Put the disk of MDF in a vice and secure one end of the banding. (if you are really at .050" it will take that radius just fine. I've done 4" at .060'' and it worked.)With a clothes iron, just sort of press your way around. When it starts to take the curve easily, tape it tightly into place. Then just work your way around. Be a little careful not to scorch the wood. Once you've gotten all the way around and are happy with the fit, you can remove half of the tape, apply glue and retape. Then do the same for the other half.

Re: Bending padouk veneer

#6

Re: Bending padouk veneer

Dan Mitchell

>Thanks for the replies, I guess water is "out".

Another reason I wanted to use this approach is that the main exposure in this application will be the disk's edge. If I made a disk out of solid wood, especially given that it's round, most of the edge would be relatively unattractive end grain.

I'll try the iron technique tomorrow.

Thanks again,

Dan

Re: Bending padouk veneer

#7

Re: Bending padouk veneer

Tony - Memphis

>What about steaming/wetting it and letting it dry around a form like you do for Shaker boxes? After it dried, you could cut and glue it. That's what I would try. Let us know what you figure out.

Tony

Re: Bending padouk veneer

#8

Re: Bending padouk veneer------WebKitFormBoundary+

Keeth Miller

>Doubling the thickness actually yields stiffness 8 times greater, not 4. As I recall stiffness varies by the cube of the thickness.

1 cubed 1x1x1 = 1

2 cubed 2x2x2 = 8

A 2 inch plank would be 8 times as stiff as a 1 inch plank.

1/32 veneer would be 8 times stiffer than 1/64.

Some of the math whizzes on the list could probably explain it better.

Keeth Miller

Buried in oak leaves in Central Virginia