Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

New House construction - Insulation question

Posts

New House construction - Insulation question

#1

New House construction - Insulation question

Terry Alexander

>Previously on this board (and I DO thank you), it was suggested that I use R50 insulation in the ceiling/attic.

What do you think is the "best" insulation for the walls. Having just said/typed that, the "best" is probably that new foam stuff that hardens. Uh....my wallet can't take that.

As always....TIA for your valued and experienced opinions.

Terry Alexander

Re: New House construction - Insulation question

#2

Re: New House construction - Insulation question *LINK*

Craig in Silverdale

>It isn't cheap, but it is the best type to install.

http://www.corbond.com/


Spray Foam

Re: New House construction - Insulation question

#3

Re: New House construction - Insulation question

paul in AZ

>this site may be of some help. You will have to do the cost/benefit calculations.

http://www.ornl.gov/cgi-bin/cgiwrap?user=roofs&script=ZipTable/ins_fact.pl

Re: New House construction - Insulation question

#5

Re: New House construction - Insulation question *LINK*

John K Jordan

>Hey, I know some of those guys! I created graphics once of their research and office buildings as part of modernization planning for the northern sector of the ORNL campus - aerial photos from helicopter, tape measure on the ground, 3D models and renderings.

I didn't know they had a web site with this information. Interesting! (You should probably start the calculator at the link below instead of the one given which assumes data has already been entered - not an elegant design!)

JKJ, retired from ORNL


USDOE Insulation Fact Sheet

Re: New House construction - Insulation question

#6

new link, energy calculations, etc *LINK*

John K Jordan

>In checking out that web site, I found a number of inconsistencies. The person in charge told me that web site had been replaced and the old one was not updated. The new link below is to a page on the new web site. The Zip Code R-value calculator is the same, but there are some other resources that may be useful.

JKJ


New link - energy calculators, etc

Re: New House construction - Insulation question

#7

Re: New House construction - Insulation question

Ken Garlock, Collin County Texas

>Terry. Do give the sprayed-in foam detailed consideration. While it my be costly for initial installation, the payback is a lot of "R" for the buck. I read that in the last 5 years urethane foam as resolved the issues with shrinkage, hence it would be a good choice. Another consideration is air penetration, The foam insulations seal the walls and prevent air flow. Less air flow through the walls, the less the HVAC bills.

Like the Fram oil filter ad said: you pay me now, or your pay me later. And pay, pay, pay. Insulation cost is a one time expense, utility bills go on, and on.

Good Luck,

Ken

Re: New House construction - Insulation question

#8

Re: New House construction - Insulation question

Grant in Iowa

>Terry,

It depends laregely on where the house is being built, and the type of construction to be used. In most areas, you can use fiberglas insulation just fine if you also do the following:

One of the big things that is often overlooked is caulking the framing before the siding goes on. In a house with a basement, the typical construction utilizes a rim joist around the outside of the floor joists. This rim joist is one of the leading causes of air leaks in the home envelope. When the framing was done on our house, we caulked the outside of the rim joist before they sheathed it, and also caulked all accessable joints on the inside of the rim joist as well before the basement was insulated.

Other areas to caulk are where the wiring and other mechanicals pass from a heated space to an unheated space (such as at the tops of walls, around vent ducting, exterior lighting boxes, exterior wall outlets (even the ones facing inward), etc. Once the wiring is roughed in, you can caulk the holes in the boxes where the wiring enters. I see many homes that on a cold day you can feel air around the outlets, which is preventable if you caulk and housewrap correctly. We also installed a vapor barrier on all exterior walls over the insulation, running a bead of caulk around the top plate before installing the vapor barrier. The only holes in the walls for air infiltration then are wherever outlet boxes occur in exterior walls, which we sealed as described above.

One year in the new house (an 1800 square foot ranch with a finished basement, bringing total finished square footage to about 3200), and we have a decent idea of our heating bill:

Above house with forced air natural gas heat, a natural gas dryer and water heater, and 4 adults living there showering and laundry etc. 6" exterior walls and R-38+ in the attic. I also heat my 1400 square foot shop to above freezing all winter(and to 60 degrees when I was in there). Our high gas bill was $180 in Iowa during the depths of winter last year. It never got above about 25 degrees F. in that entire month with many nights below zero F. Contrast that against the average summer gas bill of $35 or so to determine the actual cost of heating both the house and shop. Not bad compared to others I have talked to and way better than my old house, which sometimes hit $300. I did augment my gas heat with a woodburning fireplace, but only a day or so a week.

People were trying to twist our arms into ground source/ geothermal for a large extra cost. It didn't make sense when I crunched the numbers and considered the fact that I was borrowing the money. So, we spent our own time to insulate things carefully and well, and it seems to have paid off.

Note that the techniques we use are good for our region, but your region and climate may dictate other methods.

Regards,

Grant in Iowa

Re: New House construction - Insulation question

#9

Good timing for this writup here Grant.....

Scott in Eastern Iowa

>.....we are still in the framing stages on our addition ( dont ask why ok? )...and I was going to hit you up on this topic soon anyway.

Thanks for posting....much appraeciated !

Re: New House construction - Insulation question

#10

Re: New House construction - Insulation question

Fred Davis

>Terry,

your in Texas and it is not difficult to insulate sufficently enough that your wallet will handle it and the heating and cooling bills.

Assuming your wall framing is 2x6 , you will get R- 19 with six inch fibreglas paper covered batts.

Using spray cans of expanding foam fill all of the spaces around doors , windows, plate line at the floor , plumbing and wiring runs thru the bottom plate and so forth.

If your budget allows for it , and since your using a poured slab, get a estimate on hot water heat in the slab in conjunction with your gas fire Water Heater or like we have here , a wood fired boiler.

That form of heat is far superior to other forms and your wife will bless you when she walks bare footed on warm floors. ;-))

That is easy, but there is a host of other things to pay attention to , do not use use solid headers above doors and windows, use open framing. Wrap the exterior before the siding goes on with 6 mil Visqueen or plastic. Use a nine foot wide roll for continuous coverage without a lap joint

Tyvak is a name brand housewrap that does approximatley the same for much more.

Use at least a two foot overhang at the roof line, double pane windows and lites in the doors if they have glass.

You have heard a bunch of of suggestions about HVAC , talk to your local contractor for that information.

FredD