Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Ceiling fan????????????

Posts

Ceiling fan????????????

#1

Ceiling fan????????????

Ron Gricher

>I have 2 wall switches ran to the ceiling fan one for the light the other for the fan 2 blacks 2 whites out of the fan is a black and a white and a black wire with a white barber pole effect so it is black and white i hooked the black to black white to white and all the ground and does not work what am i doing wrong?

Re: Ceiling fan????????????

#2

Re: Ceiling fan????????????

Mike Fitterling

>The solid black is the fan motor and the black with white "barbershop" line is the lights. They share the neutral (one white wire. This is assuming it is a Hunter, but others are very similar. I just did two in our addition, switch for the lights, fan always powered. Are you certain the pull chains are clicked to the on position?

Re: Ceiling fan????????????

#3

Re: Ceiling fan????????????

Ron Gricher

>OK so all the black to black and white to white and the black and white wire goes with the white yes it is a hunter i have tried everything thanks

Re: Ceiling fan????????????

#4

Followup

Mike Fitterling

>I guess I am not understanding what you have clearly.

Does the power come from the switch box or does it come down from the light box via two switch legs?

If the power comes from the switch box (and the light and motor are on the same circuit) the whites coming into the box from the panel should be tied together with the whites coming down from the fan box, and the black coming from the panel should go to one side of the switches. Then the blacks coming from the fan box should go to the other side of the switches, one to each. The grounds should all be tied together and to the boxes.

If the power is coming down from the fan box via switch legs, then from each wire the black should go on one side and the white should go on the other side of each switch. The whites in this case should have been marked as hot (black) in some manner, usually by a piece of black electrical tape at its end. In the fan box, then, the power coming in from the panel should have its blacks tied to the blacks going to the switch via the switch legs and its white tied to the white from the fan. The returning white wire coming up from the switches via the switch leg should be hooked to each black on the fan. Of course, the grounds should still be hooked to gether and to each box.

You have to know where the power is coming from to ge tthis right.

Good luck and be careful. Use a tester if you do not know which is which.

Mike

Re: Ceiling fan????????????

#5

Re: Ceiling fan????????????

Mike Fitterling

>See my Followup below.

Re: Ceiling fan????????????

#6

Re: Followup

Ron Gricher

>Alright mike i have 2 sets of wires coming from the wall to the ceiling one set is for the fan and the other is for the lights 2 blacks 2 whites and 2 grounds the light-fan is a hunter The Westminster has 1-black 1-white 1-ground 1-black-white wire coming out of it i have hooked this thing every way possible and it still does not work i guess it could be a bad product thanks again for your help

Re: Ceiling fan????????????

#7

Re: Followup

Carol - now back in Dubuque, IA

>You could have a bad unit, Ron, but you still need to know where the source of power is. In other words, when all the wires are disconnected, which one is hot and which box is it in? It will be at the switch box or the ceiling box. When you have determined that,then re-read Mike's help.

Good luck.

Re: Ceiling fan????????????

#8

Re: Followup

Ron Gricher

>now it is running with the switch on or off now what i have black to black white to white and white to the black and white what now

Re: Ceiling fan????????????

#9

Re: Followup

John McGaw

>Things seem to be getting in a muddle here. But when you say that the fan runs regardless of the position of the switch that suggests to me that the power (the wire that runs back to the breaker box) must be coming down in the ceiling box. What is the light doing now? Is it on all the time or not working at all?

I think that you need to do an inventory of wires in the boxes. You say that you have two sets in the switch box (2 black, 2 white, 2 ground) so that is fine. That means that you must have at least an equal number of sets in the ceiling box if the wires indeed run straight up there. But, ignoring the wires you can see coming out of the fan, what other wires do you have up there? It seems that you pretty well would have to have a spare black, white, and ground which leads back to the breaker panel. That or there is a box we don't know about (or possible something supernatural is happening).

Re: Ceiling fan????????????

#10

Re: Followup

Ron Gricher

>I went out to lowes where i bought it and here is how it is wired one black out of ceiling to the fan all whites wired together and finally the and black-white coming out of the fan goes to the other black and it works perfect thanks to all of you for your help.

Re: Ceiling fan????????????

#11

Re: Followup

Mike Fitterling

>Glad you got it working, Ron.

Cheers,

Mike

Re: Ceiling fan????????????

#12

Ellis Walentine

Whew, that was exhausting

Ellis Walentine

>Thanks, Mike (and others), for diving into this. Now I know where to come with my next electrical dilemma.

Cheers,

Ellis

Re: Ceiling fan????????????

#13

Electricity is so simple and so mystifying

Bill Houghton, Sebastopol, CA

>When I briefly worked as an auto mechanic, years back, before many of the now-necessary electronic stuff, the most mysterious part of a car to most mechanics was the electrical systems.

As you found, Ron, tracing the path can be confusing - but it's the only way to do it. I have, more than once, drawn out the schematic, the path the wires are following, in order to sort out what's going on.

Re: Ceiling fan????????????

#14

Re: Ceiling fan????????????------WebKitFormBoundar

Ronald------WebKitFormBoundaryAA5MAAC+AAX9AALx

>Ron, you have to tell where the wire from the panel is at. Either at the light-fan or at one of the switch boxes. Once this is found then someone can help you a whole lot easier.

------WebKitFormBoundaryAA5MAAC+AAX9AALx