Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

rubbing out finish question

Posts

rubbing out finish question

#1

rubbing out finish question

Bill Tindall, E.TN

>Well, the French footed Federal Wall cabinet is done except for final finish refinement. Wife says as coated shellac is too bright (I agree), and 4/0 wool and wax is too dull. Is there a route to something in between?

Re: rubbing out finish question

#2

Ellis Walentine

Couple possibilities

Ellis Walentine

>One method that works for me is to sand up through the appropriate grit of wet/dry paper, say 2500. Another way is to use an automotive glazing liquid of the right gloss level.

Ellis

Re: rubbing out finish question

#3

Doesn't Wax Create A maintenance Issue?

howard

>so that every so often the piece needs to be rewaxed? or does this require much less attention than that?

Re: rubbing out finish question

#4

Re: rubbing out finish question

Clint Searl, at the base of Haycock Mtn

>Overspray with S-W Medium Rubbed Effect Alkyd Lacquer. It's beautiful; neither too glossy nor too dull.

Clint

Re: rubbing out finish question

#5

question

Bill Tindall, E.TN

>will the auto stuff leave anything in the mahogany pores that will be light color and detract?

Re: rubbing out finish question

#6

Re: rubbing out finish question

Ken Oakley-Sunny St. Cloud, Fla

>Years back a man I knew who made and refinished founiture would use nothing but powdered pumice and crude oil to rub out his finish. I used it myself back in the 60's and 70's. Really smooths a finish but takes some elbow grease.

Re: rubbing out finish question

#7

Re: question

Sgian Dubh

>"will the auto stuff leave anything in the mahogany pores that will be light color and detract?"

In my experience the answer is yes, whether you use automotive burnishing pastes or pumice and rottenstone. The exception to that is burnishing over a fully filled grain if you are dealing with either an open grained wood like oak, or semi-open pored wood like mahogany or walnut.

If you want to avoid that white stuff in the grain look you might want to consider a polish where you can get the sheen you want using other means, eg, a 10%, 30% or 50% sheen lacquer applied with a spray gun; or rub down shellac using, for example, wet and dry papers, wire wool or nylon abrasive pads plus a lubricant, eg, white spirits (aka mineral spirits).

The fly in the ointment bit with this abrasives method when done on open pored woods is that the abrasive doesn't always get into the bottom of the pores leaving shiny bits grinning up between the dulled bits. Slainte.

Re: rubbing out finish question

#8

Re: rubbing out finish question

Bob Lemon Sacramento Ca.

>After using the 4-0 steel wool, rub up the shine with paper towels or a brown paper bag. This will give you a soft sheen without having rubbing compound all over everything. Try this on a small area that DOES catch the light, otherwise you won't see the shine in the dark.

Re: rubbing out finish question

#9

Re: rubbing out finish question

Fred Davis

>Ellis and Bob both have a appoach that works well, if you go auto rubout componds , look at the Mequiars line, they are pink in color and I use them all of the time for adjusting sheen.

They come out of the bottle pink in color and if any remain after wiping down with a cotten cloth, then a little colored funiture polish does the trick..

Brown paper towels or butcher paper works also , grocery type bags sometimes have a finish on them.

FredD

Re: rubbing out finish question

#10

problem solved

Bill Tindall, E.TN

>Mahogany Briwax plus rottenstone on a foam rub out pad. The gloss is between 4/0 wool and native shellac, just what I wanted. The rottenstone is gray and it did not change the color of the pores which I had already made dark with a dark glaze. I will 4/0 wool the cabinet frame and polish the crotch door panels and top to bring them up a notch in luster.

thanks to all for suggestions

Re: rubbing out finish question

#11

how I rub to semi-gloss

Michael Dresdner

>Use the same technique and the same 0000 steel wool, but instead of paste wax as the lubricant, use automotive rubbing compound. The combination of the compound and steel wool gives you a very nice semi-gloss.