Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

Crayon on wood

Posts

Crayon on wood

#1

Crayon on wood

Steve in Fresno (Go Dogs)

>My dear sweet son, decided to decorate some wood that I'd planed down to exactly 1/4 thick for some small boxes. Is there anyway to remove the wax from the wood? I'm afraid of running it through the planer again and getting the wax on the blades, and that transfering to the next project.

Thanks for any input.

Steve

Re: Crayon on wood

#2

JL

You can try mineral spirits

JL

>or toluene. But I would "decorate" a test strip first and try it on that.

Re: Crayon on wood

#3

scraper

Bill Tindall, E.TN

>a card scraper will remove it easily. Do not try to dissolve it or it will penetrate the wood.

Re: Crayon on wood

#4

Re: scraper

Fred Davis

>Bill 's sugestion is about right for wax, paint thinner will disolve it, I would before using the card scraper , put it in a freezer for awhile, then the wax will back off of the the wood easier and faster.

FredD

Re: Crayon on wood

#5

Re: scraper

Steve in Fresno (Go Dogs)

>Scraper it is, it's 6 feet so I guess I'll chop up some curley.

Then the kid!!!!!!!!

Thanks

Steve

Re: Crayon on wood

#6

not the worst thing a kid did

Bill Tindall, E.TN

>We never did custom planing unless we sold the lumber. But this guy came with some prime chestnut he had taken off an interior wall of an old house. The boards were wide and still bright, with few nail holes. He had meticulously removed all nails and scanned with a metal detector. I caved and said I would plane it. A that time we didn't have dust collection and the shavings just shot out the back of the planer. While making the first pass the person on the out feed kept flinching like something was hitting him. Finally I stopped the machine to see what was the matter. It soon became apparent that the boards had a multitude of ridges on the just planed face. I was hitting something metal.

Examination of the boards that had not yet been planed revealed bright, unrusted #4 finishing nails driven haphazardly at various angles. We went through the remaining lumber pulling out a dozen or so new nails and finished the planing job. I called the lumber owner with the bad news that the planing bill would be substantially more than he was expecting because we had hit nails. He was dumbfounded how we could have hit nails given the care he had taken to check for nails. Then I told him they were NEW nails. After a short pause he began to grumble at a revelation. He had left his son alone with the pile of lumber. The son had his own hammer and apparently a desire to pound something with it. I went easy on the dad for fear my wrath would be multiplied upon the son.

Re: Crayon on wood

#7

Re: not the worst thing a kid did

Steve in Fresno (Go Dogs)

>Ouch, for both Dad and your planer!!

The scraper did it's magic, and Dear Son held the wood for me and even did a little of his own scraping. I'll see if I can get some pic's of the boxes uploaded today.

I think they turned out pretty darned cute.

Re: Crayon on wood

#8

Re: scraper

Howard Acheson

>>> paint thinner will disolve it

True, but it also will cause it to migrate deeper into the wood. After all, paint thinner is a thinner. I would much prefer using a scraper first. Maybe a paint remover to get the residue.

Re: Crayon on wood

#9

Re: scraper

Fred Davis

>perhaps I was unclear, happens occasionally, when I said "paint thinner will disolve it" that is what I meant.

I did not say use it, because of the adsorption into the wood that the solvent would cause .

I did agree with Bill on the use of the Card scraper and would have reccomended it even if nobody else did and I also suggested to put it in a freezer to stiffen the wax and make the job easier.

FredD

FredD