Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

What wood is best for printing?

Posts

What wood is best for printing?

#1

What wood is best for printing?

Xeon

>Hi,

I need to print graphics and pictures onto small pieces of wood, so is

pine wood the best?

Does anyone know of other wood which is more suitable for pictures to be

printed on? Any recommendations?

(some wood are not suitable for picture printing due to the nature of the wood)

What about 5-layer birch plywood? I went to Woodfinder.com but got totally overwhelmed by the amount of wood there. I'm not a woodworker so I'm new to all these, but I need to print graphics onto wood.

Thanks for any advice! I'm totally lost.

Xeon

Re: What wood is best for printing?

#2

Dale Lenz

Re: Several years....

Dale Lenz

>ago we "ink stamped" information on some 3"x3"x1/2" wood blocks, carbon storage modules, I believe we called them. The stamped ink ran in the grain of pine. On the hardwoods we use, oak, cherry and others, the print came out fine.

So.....don't know if the above info help you or not(?). Let us know what you find out.

Re: What wood is best for printing?

#3

Re: Several years....

Ken Oakley-Sunny St. Cloud, Fla

>I have had my best luck using well sanded or scraped White Birch and, or Hard Rock Maple.

Re: What wood is best for printing?

#4

Plus

Ken Oakley-Sunny St. Cloud, Fla

>I think I sprayed some lacquer based sanding sealer on the wood before the printing was done

Re: What wood is best for printing?

#5

JL

Solid or plywood?

JL

>If I was going plywood, I'd suggest either maple or birch plywood.

If I was going solid wood, I'd suggest a reasonably tight-grained light colored wood. Holly comes to mind (and maple too).

You may also want to look into wood bleaching procedures.

My $0.02

Re: What wood is best for printing?

#6

Ellis Walentine

Re: What wood is best for printing?

Ellis Walentine

>You didn't mention what kinds of inks you will be using. Some inks, like screen printing inks are quite viscous and will not be so easily sucked into the wood fibers as watery inks. There is also the issue of transparency to think about. You don't want a wood that has features that will telegraph through a transparent or semi-transparent ink. For these reasons, I would suggest a light-colored, hard, close-grained, diffuse-porous wood, possibly rock maple, yellow birch or something similar. On the softer, cheaper side, there are basswood and yellow poplar, although these are more likely to wick the ink and create runs. Whatever wood you use, it would probably be a good idea to coat it with some lacquer or Krylon matte spray beforehand, and then sand back down to the finished wood (or not). The finish will penetrate and seal the surface fibers and reduce the amount of ink that is absorbed.

Experimentation is key here. Woodfinder will certainly help you find sources for the woods I mentioned.

Ellis Walentine, Host

Re: What wood is best for printing?

#7

CHERRY!!!

Ron Bauman

>all the old type I've seen had been cherry.

Re: What wood is best for printing?

#8

Re: What wood is best for printing?

Xeon

>Thanks a lot, guys! One supplier I contacted says that based on his experience, 5-layer birch plywood is best for printing, so maybe I'll go with that.

Btw, for a piece of birch plywood at 4" by 4" by 0.2", it costs US$1.50 per piece. Is that considered expensive? Or reasonable?

Thanks! :-D

Xeon

Re: What wood is best for printing?

#9

Re: What wood is best for printing?

Xeon

>Oh, and just to add......I'll be using a heat-press and transfer paper to print graphics onto the birch plywood. Sounds good? :-)

I'm concerned about the transparency, though, because there might be a "squarish border" around the image.

Re: What wood is best for printing?

#10

Dale Lenz

Re: My last piece of Baltic Birch...

Dale Lenz

>plywood that is approximately 5'x5' by 1/2" was 25~30 dollars I believe.