Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

Best way to strip hard maple.

Posts

Best way to strip hard maple.

#1

Best way to strip hard maple.

Dan Mitchell

>My parents had a set of Ethan Allen living room furniture which they bought in the'60's. Coffee table, 2 "dough box" end tables, and a step table, all made out of ~3/4" maple. Long story short, after some family transitions, I have the panels from these tables (tops, larger side pieces, etc.) which I would like to use for a couple projects. I'm wondering what the best approach to stripping off the old finish would be. To further confuse matters, I had refinished the tops of 3 of the tables when I was a teenager, back in the mid '70's, and I don't recall if I used polyurethane or lacquer. I remember it was a Deft product. Should I use a stripper, if so, which is best & has the least objectionable fumes, or should I sand the old finish off, or is there another approach? Unfortunately, all the panels are too wide for my DeWalt 734 planer, though I may end up having to cut some to a narrower width, depending on what I end up building.

Any helpful comments appreciated!

Dan

Re: Best way to strip hard maple.

#2

Ellis Walentine

Strippers *LINK*

Ellis Walentine

>You might want to order one of the "Circa 1850" strippers from Swing Paints, one of our sponsors. They make a whole range of friendly and efficient strippers for all kinds of finishes.

Ellis Walentine, Host


Swing Paints

Re: Best way to strip hard maple.

#3

Darn :-(

Thomas Skaggs, Foothills of Mount Level

>I was so dissapointed by this link. I really thought it was something entirely different.

Tom

Re: Best way to strip hard maple.

#4

Re: Best way to strip hard maple.

Howard Acheson

>I recommend you use a stripper containing methylene chloride. It will be best are removing any type of finish with the least chance of leaving a residue. It will also remove the finish with a single application.

One thing I would check is whether the panels are solid wood or veneer. Much of the Ethan Allen stuff I have seen was veneer over a composition material substrate.

Re: Best way to strip hard maple.

#5

Re: Best way to strip hard maple.

Dan Mitchell

>I've used the methylene chloride variety before (same chemical used to decaffeinate coffee, BTW), but I was wondering if there was another choice.

The tables in question are about 45 years old & definitely solid maple.

Thanks for the reply.

Dan

Re: Best way to strip hard maple.

#6

Re: Strippers

Dan Mitchell

>Thanks Ellis, I'll check it out.

Dan

Re: Best way to strip hard maple.

#7

Re: Best way to strip hard maple.

Howard Acheson

>>> I've used the methylene chloride variety before (same chemical used to decaffeinate coffee, BTW), but I was wondering if there was another choice.

Sure, there are other choices but by far, the fastest is one containing methylene chloride. Follow the directions on the can.

BTW, there aare no "safe" paint strippers. Some contain chemicals that may be somewhat less toxic but none are non-toxic.

Re: Best way to strip hard maple.

#8

Re: Best way to strip hard maple.

Greg

>The cleanest, and by far the easiest way to strip the old surface, is to plane it. Bite the bullet and rip it it in to 12 inch strips on plane a very small amount off the thickness. You will be ready to reuse the wood immediately without the stench and cleanup issues of a stripper chemical.

Greg

Re: Best way to strip hard maple.

#9

Re: Best way to strip hard maple.

Fred Davis

>Dan,

If you use a plastic sheeting like Saran Wrap over the stripper while it is still wet, you will speed up and imprrove the process , regardless of the type of stripper you use.

FredD