Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

A case for spraying finishes

Posts

A case for spraying finishes

#1

A case for spraying finishes

Bill Tindall, E.TN

>The picture is a close up of the trunk lid. Note the varnish is glass smooth. It dried that way because it was applied smooth with a spray gun. I can't get a finish this smooth with a brush.

I spray everything I can- lacquer, varnish, paint, shellac. (I don't spray oil stains. They go on with a pad. ) I don't see a reason not to buy spray equipment and spend some time to learn to use it. It saves so much time and the result a smooth finish.

Re: A case for spraying finishes

#3

Ellis Walentine

A good case

Ellis Walentine

>I've always sprayed lacquer and related finishes, but I only sprayed varnish a few times. I found that the longer tack time invites runs, unless you're spraying it on horizontal surfaces, and then you need to pay strict attention to dust control or else airborne dust will settle into the fresh film, which takes much longer than lacquer to dry dust-free. I never was able to control the dust well enough, although I found that suspending a clean piece of cardboard or plywood over the fresh film helped a lot. Also, anyone contemplating spraying varnish with the same equipment as they use for lacquer should be aware of the possibility that a different tip will be needed for the different viscosity and that you will need to clean your gun and cup thoroughly, which should go without saying. It is also imperative to wear an appropriate dust/vapor mask, as the varnish will really gum up your nostrils, and presumably your lungs, if you don't. I guess lacquer can hurt you too, but I always found the varnish overspray to be particularly unpleasant.

But, the evidence speaks for itself. The finish on that coopered lid looks wonderful.

Ellis

Re: A case for spraying finishes

#4

Looks fantastic

Dan Mitchell

>What equipment do you use?

Re: A case for spraying finishes

#5

how to be dust-free with varnish

Bill Tindall, E.TN

>after spraying I tuck the piece in one of our fleet of ancient vehicles, in this case the Explorer. The amount of dust I experience is insignificant. Letting the piece dry outdoors would not do at all.

Once one learns to spray shellac everything else is very easy. I use the same cap for everything and thin as necessary.

Re: A case for spraying finishes

#6

spray equipment used

Bill Tindall, E.TN

>Ancient suction feed DeVellbis gun with 3M PPS cups. Love those PPS cups. One can spray upside down or any other way and clean up is a breeze.

I tired HVLP, or what ever abbreviation it goes by, and I didn't like the atomization I got. Maybe lack of experience with the new technique.

Re: A case for spraying finishes

#7

Re: A case for spraying finishes

John K Jordan

>When I worked at the Berea College woodworking many years ago, everything was hand-sanded and finished by spraying. I thought the finishes were beautiful, even on the toys. To minimize dust and control vapor they had an entire room just for spraying. If I remember correctly (40 years ago), most was lacquer.

Your finish looks nice.

JKJ

Re: A case for spraying finishes

#8

Re: A case for spraying finishes

Fred Davis

>Right you are Bill, I can't remember the last time it was necesary to rub out the lacquer I apply with a Graco airless and a double orfice stacked tip that makes the finish look like it was on sheetmetal.

I never run anything but Lacquer and sealer through the rig.

FredD

Re: A case for spraying finishes

#9

Cleanup is always the biggest pain for me

Tim Greif - West of Chicago

>I've sprayed a bunch of things over the last 30 years - cars, motorcycles and boats - all with lacquer. My only furniture experience with spraying was last summer, I sprayed some old furniture with shellac.

I always dread the cleanup of the equipment. To me, unless you're doing a bunch of stuff, the hassle of cleanup outweighs the advantages of spraying. I don't like piano gloss finishes, so a final coat of wipe-on varnish thinned 50/50 with naphtha gives me all the smoothness I need.

If you don't find cleanup a hassle, I'd love to know your secret.

Re: A case for spraying finishes

#10

Re: Cleanup is always the biggest pain for me

Chuck Jurvelin

>I have sprayed finishes on wood,metal, sheetrock, and any other surface for years. I have both an HVLP gravity feed BINKS and a BINKS Model 7 siphon feed gun as well as a couple of cheap pressure guns. Clean-up is not that difficult- simply rinse out cup, run appropriate thinner thru it, then partially fill gun with lacquer thinner, spray a little to clean orifices, and hang up gun. Unless you are not going to use gun for extended period, this is adequate. I probably completely disassemble gun about three or four times a year. My finishes are far superior to brushing and take a lot less time. I will admit, a little practice in how heavy to apply finishes is necessary, but you'll learn quick!

Re: A case for spraying finishes

#11

Re: Cleanup

Mark Mandell - Gone Round In Jersey

>Ain't no thing with waterbornes. Empty the gun, purge any material lines, rinse with water, hang up to dry. [See thread below on spraying WB]

Re: A case for spraying finishes

#12

Re: Cleanup

Chuck Jurvelin

>Even if I shoot waterbase, which is quite frequent, I do my final rinse of the gun with lacquer thinner and leave a little in the pot. This seems to inhibit any drying out or any rust from the previous waterbase finishes. Waterbase actually seems to collect and harden worse than a solvent based finish on inner parts of the gun.

Re: A case for spraying finishes

#13

Re: Cleanup is always the biggest pain for me

Fred Davis

>The secret is sizing the equipment to the job.

If your doing some stuff like toys , I use a Binks touchup cup gun, very small and very easy to clean.

Kitchen cabinets and furniture brings out the airless and cleanup with that one only entails running solvent thru the hose and gun which I am already doing when I mist overspray and flat surfaces with a light coat of solvent as a last step in the process.

FredD

Re: A case for spraying finishes

#14

I'm puzzled, cleaning is easy

Bill Tindall, E.TN

>Cleaning a spray gun, at least mine, is easy.

1.Finish spraying, which will take way less time than any other method.

2. Drain remaining finish.

3. Add about 1-2 oz solvent to cup. Shake, spray and drain. (I save the washings for diluting finish at some future time)

4. Repeat step 3 twice more.

5. the end

About every 5 years I take the gun apart and give it a good cleaning.

With the 3M PPS cups it is even easier.

1.Remove cup and toss

2. Add a tsp. of solvent to pick up tube and spray

3. Repeat step 2 twice more.

Re: A case for spraying finishes

#15

Re: Solvent

Mark Mandell - Gone Round In Jersey

>Chuck,

I think I'd be shy of putting lacquer thinner in my WB guns as you describe only because of the possibility of residue messing with the WB chemistry in the next use. To insure drying of the rinse water, I'd suggest regular DNA as it's water-miscible, and will speed drying but not interfere with finishes of you first put some pure water through the gun/system before adding finish. My guns are all stainless steel in the wet parts so I don't worry about rust. I do disassemble and check things for residue once in a while, but so far (3-4 years) everything's stayed nice and clean. Fuhr finishes used to build a little tube on the air cap port (flicked off with a fingernail), but I haven't had that happen with the Target and General finishes I use now.

Just a few thoughts.

mm

Re: A case for spraying finishes

#16

Bart Goldberg

Re: A case for spraying finishes

Bart Goldberg

>I've been wanting to get into spraying for quite a while now. I would be interested in suggestions of equipment to purchase for a newbie to spraying. I do not have a large compressor - a Porter Cable double stack for running my nail guns.

To date, I've done only used hand applied finishes and use Waterlox most of the time, and occasionally use Barley's Gel Varnish.

Equipment suggestions would be most welcome - budget? say - up to $1,000.00

Thanks In Advance

Bart

Re: A case for spraying finishes

#17

Shprayanzies

Mark Mandell - Gone Round In Jersey

>Bart,

You're welcome to drop up here and take a look at my rigs.

mm

Re: A case for spraying finishes

#18

Re: A case for spraying finishes

Clint Searl, at the base of Haycock Mtn

>1. Invest in a good gravity feed conventional gun; Sata or DeVilbiss

2. Pick a finish. I depend on solvent based lacquer because it gives a great finish, it's forgiving and easy to apply, and cleanup is a snap.

3. Consider a two stage stationary compressor. You'll never regret it.

Clint